Frigidaire Logo

Frigidaire Popular Questions, Answers, Tips & Manuals

  • 3K Products
  • 135K Answers
  • 3M Views

Microwave - Explanation of the Child Lock Out Feature
  • Press and hold the CLEAR/OFF pad for 3 seconds. The display will show "LOCK" and then revert to the time of day.
  • A small "L" may appear in the corner of the display as a reminder that the control panel is locked. ...
  • Press and hold the 5 and 7 pads simultaneously for 3 seconds.
  • Press the Mute pad for 3 seconds.

Microwave - Explanation of the Child Lock Out Feature


https://products.geappliances.com/appliance/gea-support-search-content?contentId...

Frigidaire... | 157 views | 0 helpful votes


yes you can, look online for parts and prices, compare to local prices.

Frigidaire... | 127 views | 0 helpful votes


www.repairclinic.com will show the breakdown and replacement instructions and will carry the parts needed.

Frigidaire... | 142 views | 0 helpful votes


Sounds like the defrost drain at the bottom of the freezer section is frozen over and clogged.
shut the refrigerator off, remove the food in the freezer
remove the shelves
remove the lower panel on the rear wall
at the bottom is the drain pan with a hole
my guess that it is full of ice?
use hot sink water and remove the ice
then use a turkey baster to clear the hole and the hose.
If the water still won't drain your going to have to manually clean the hose.

Frigidaire... | 91 views | 0 helpful votes


You have a shorted door switch or a loose, misaligned, or broken door switch mount. It's probably the top or bottom door switch, not the middle one.

Frigidaire... | 180 views | 0 helpful votes


H1 means the refrigerator or freezer side is to warm
Are the controls set properly?
Is the rear wall of the freezer full of snow?
Is the outside edge of the refrigerator warm or hot to the touch?

Frigidaire... | 73 views | 0 helpful votes


Fridge/freezer freezing up- and no fan or air circulation:

first check the defrost terminator thermostat it may have gone out. Thus not allowing the heating element to melt the ice.

AT TIMES The fan usually stops working AND CAN MAKE FUNNY NOISES AS WELL due to ice obstruction when the defrost terminator has gone out and u get ice build up? u can check the terminator with a multi meter for continuity but do not check at room temperature. stick the terminator in cup of ice water for 20 minutes then check it for continuity, should be closed when cold and open at room temperature.

May also need to check the defrost timer, The defrost timer is usually found behind the front grill "toe kick" of the refrigerator. Or in the fridge compartment near middle top section.

u can get by and test manually by placing a small screw driver into the tiny slot or hole underneath the timer and turn slowly clockwise till u hear 1 click. this will engage ur defrost cycle in about 15 minutes u should be able to come back and feel the heat in freezer as it melts the ice providing ur terminator is not bad?

Another way to test it is with a multi meter. Remove timer it from fridge and you will see 4 prongs numbered 2,1,4,3 in that order. Place ur meter prong on prong 1 & 3 (if your fridge has a capacitor wired in series with the windings, then u check for micro fares rather than OHMS) If u cannot confirm this test, still try the next.

Take ur meter prong and connect to prong 1 & 4, it should read resistance or ohms ( closed) now remove prongs and place on prong 1 & 2, this should now read infinity or open (no ohms) now take a small screwdriver place it in the tiny hole or slot under the timer. Turn it clockwise slowly till u hear 1 click. Now ur 1& 2 should read closed ( showing ohms or resistance) now place meter prongs on 1 & 4 and you it should now show open ( or no resistance - no ohms) this is how u know ur timer is good, Remember when testing for ohms ADJUST meter to use a high ohms rating in the thousands as the resistance is very high in OHMS. And adjusting to low ohms rating may give a false reading or not show the proper resistance..

Another item to check with a meter is the heating element itself. Located under the evaporator coils. It should show continuity or resistance OHMS WHEN TESTED AT BOTH ENDS OF THE PRONGS .

Lastly check the cold control thermostat with a meter for both OHMS and volts ( VOLTS is a live test with fridge plugged in so be careful) It must show 110 volts. An open or thermostat that reads infinity will not allow the proper cooling and defrosting cycles to operate and may in fact stop anything from happening as if there is no power to the unit?

ALSO CHECK THE AIR FLOW VENT SYSTEM and THERMISTORS At times it can get stuck to far closed or open. Some units feature a digital electric adjusting vent system while others are manually set. Check for any ice build up or other obstruction in the vent damper, see if u can manually open or close it. Some times when u have the settings set to the highest it closes off one area while allowing to much cold air flow to the other area!

THERMISTORS in the freezer and fridge section for continuity OHMS and for amount of OHMS current being put out. In most models around 1300 ( give or take 150 ohms) ohms is required

Fridge Warm Defrost Thermostat Testing Troubleshooting Refrigerator Repair Frosting up in freezer not cooling Admiral RSCA207AAM
defrost timer location defrost terminator-o11xkkle5vgwwhdb5hsjckpk-1-0.jpg

defrost thermostat test -o11xkkle5vgwwhdb5hsjckpk-1-2.jpg

defrost timer refigerator temp control and defrost timer-o11xkkle5vgwwhdb5hsjckpk-1-5.jpg

defrost timer testing defrost timer pins-o11xkkle5vgwwhdb5hsjckpk-1-9.jpg

Frigidaire... | 149 views | 0 helpful votes


Unfortunately, the SY EF error can mean a problem with the electronic control board or the fan. Check your wiring. It's possible that the wiring harness isn't fully seated (at the fan in the freezer or the electronic control board) or one of the wires in the harness is broken. If those are okay and the problem persists, then a new control board is needed.

I wish that I had better news for you.

Cindy Wells

Frigidaire... | 96 views | 0 helpful votes


The Frigidaire GLTF1240A clothes washer has a tub capacity of 2.65 cubic feet. Under typical conditions, based on a yearly average of 392 loads of laundry, the Frigidaire GLTF1240A is estimated to use 341 kilowatts of energy per year. Obviously, this number will vary depending on things like the size of loads that you wash, and temperature at which you wash your clothes. Also, this figure is calculated according to a test done by the US Department of Energy which takes into account the energy consumed by the washer as well as the energy needed to heat the water with an electric water heater. If you use a gas water heater you will probably use fewer kilowatt hours but you will consume gas to heat the water.


Its estimated water use is 9,806 of gallons per year. It is estimated to use 9.4 gallons per cycle, per cubic foot of tub volume. You can use this "per cycle, per cubic foot" to compare washers against each other. The lower the number, the more efficiently the washing machine uses water, assuming your clothes are equally clean after being washed in either washing machine.

Frigidaire... | 372 views | 1 helpful votes


According to your model number a bypass plug wont work. Refer to owners manual. I dont think they make a bypass plug for your model.

Frigidaire... | 59 views | 0 helpful votes

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18342 Answers

Cindy Wells

Level 3 Expert

6099 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...