Frigidaire Logo

Frigidaire Answered Questions & Fixed Issues

  • 3K Products
  • 135K Answers
  • 3M Views

Hi,
You have a leak in the refrigeration system...that is why it is not cooling and condensing water and why it is dripping oil...

Here is a tip that I wrote to help people tofigure out what is going wrong with their dehumidifier

Dehumidifier is running but no water is in bucket

heatman101

Frigidaire... | Answered on May 28, 2020 | 784 views


Hi,

As the weather is getting warmer for many people their freezer and/or refrigerator do not work right because of a dirty condenser coil...there are also many other things that can go wrong. If you are hearing a clicking or buzzing then check out the last two tips.


If your refrigerator is running but warm, then…


Check out this tip that I wrote about that... it is a great place to start trouble shooting your unit...and something that you can do rather then calling a repair person to do a simple thing for you...

Refrigerator Condenser Coil Cleaning Refrigerator Repair
http://www.fixya.com/support/r4024657-refrigerator_condenser_coil_cleaning

Refrigerator Troubleshooting Refrigerator Compressor
http://www.fixya.com/support/r3885294-refrigerator_troubleshooting

Refrigerator Compressor Start Capacitor and Start Relay
http://www.fixya.com/support/r4023749-refrigerator_compressor_start_capacitor

heatman101

Frigidaire 14.1... | Answered on May 25, 2020 | 4,407 views


Upright freezer door was ajar, alarm went off. Where is the reset button? Product is Frigidare.

Frigidaire 20.6... | Answered on May 25, 2020 | 4,971 views


The Amber light is the Power 'On' indicator. The Red light is a Temperature Alarm indicator. THe Red light comes on if the freezer compartment rises above 20 degrees F (for example a freezer malfunction or someone left the door open). You also probably have a rocker switch (or two holes that are over a rocker switch) that is in between these two indicators. If you do, that's an audible (loud buzzer) alarm when the red light comes on. The rocker switch is a simple on-off switch to silence the alarm or turn it back on.

Frigidaire 20.6... | Answered on May 25, 2020 | 6,385 views


Hello - Typically "OF" indicates that the freezer is turn off. To activate freezer, press UP three times until display shows "1" then press UP to desired setting. If it will not allow you to change setting and freezer continues to be off, try resetting the freezer by unplugging it or flipping the breaker off. Wait approximately ten minutes and turn it on. If "OF" continues to display, the unit could possibly have a communication problem with the electronic control assembly. Contact a professional to move forward accurately.

Frigidaire 20.3... | Answered on May 25, 2020 | 6,710 views


call a repair service or go buy a new one

Frigidaire... | Answered on May 25, 2020 | 848 views


Make sure that the cooling coils are clean. Also that the cooling fans are working. It may have lost it's treon and it is time to buy a new one.

Frigidaire... | Answered on May 20, 2020 | 30 views


PF is showing you that there is a power problem. Check your dryer circuit breaker at the power panel. This can be a sing that one of the 2 breakers has tripped. Push the CB hard to OFF and then back to ON. Then try and start your dryer. If that does not work just respond here and I will help you.

Try selecting "No Heat" after resetting the CB and see if the dryer starts. If it does you could have a bad heating element that caused the breaker to trip to begin with. Sometimes when the heating element fails the broken link will contact the chassis and cause the CB to trip. Heating element failures are usually caused by poor airflow. You may want to look for any signs of lint in your dryer to include the lint filter area and all the way to the outside wall exhaust point.

Kelly

Frigidaire ... | Answered on May 13, 2020 | 2,093 views


When you replaced the thermistor, did you check the resistance of the wiring and temperature sensor back at the control board? If the wires are damaged or the connector at the control board has corrosion, the control board won't get the correct signal information. If those are fine, then the control board is probably faulty. Sears Parts Direct has the control board here: https://www.searspartsdirect.com/product/3jlv6aqwdo-0046-253/id-5304512769 . Other repair shops will have this part as well.

I wish that only the refrigerator temperature sensor was faulty. I hope this helps.

Cindy Wells

Frigidaire... | Answered on May 11, 2020 | 34 views


The E11 error code indicates a problem with the gas sensor DE32-60011A and or the wire harness DE39-40678D. Unfortunately the manufacturer has discontinued the sensor. You may want to try contacting local parts dealers, one of them might still have it in stock. Enter your part number in a search engine, a smaller company might have it or try eBay, Amazon or similar sites . Search by using the manufacturers part number. Try a used appliance store, sometimes they have the same model or a usable part for your machine.

Frigidaire... | Answered on May 07, 2020 | 3,099 views


https://www.justanswer.com/appliance/9t2ld-frigidaire-side-side-model-ffhs2622msu-flashing.html

Frigidaire side by side Model Ffhs2622msu Flashing H on the ...

www.justanswer.com > ... > Evaporator Coil Questions
1 answer
Jul 14, 2016 - The damper is not the problem. The problem is the unit isn't defrosting properly. H means that the refrigerator thinks the heater is bad. You'll ...

SOLVED: What does the ( h) code mean on my refrigerator ...

www.ifixit.com > Answers > View > What+does+the+(+h)+code+mea...
1 answer
Mar 26, 2019 - What does the ( h) code mean on my refrigerator. What does the ( h) code mean on my refrigerator 2013 Frigidaire side by side my refrigerator isn ... My frigidaire refrigerator stopped cooling ...
3 answers
Jun. 4, 2018
SOLVED: Fridge won't hold temperature settings ...
3 answers
Apr. 26, 2016
More results from www.ifixit.com

Frigidaire... | Answered on May 04, 2020 | 35 views


Had this problem and called customer service and they had no idea. Turns out it's an alert that the suspense is jammed (DISP). Clear it out with your hand and you should be good to go. I figured this out after my kitchen was full of puddles when I got home from work.

Frigidaire... | Answered on Apr 28, 2020 | 6,199 views


Sorry to read about your problem.

Sorry no reset switch.Their is a 80% chance you have a defective heat coil or coils. or the heat selector switch is defective. in addition you may have a clogged dryer vent.

I suggest you place a call to a service company.

I tried to help you. Please help me and vote/rate this response thanks.
If you live in Denver area, I can help you.

Frigidaire... | Answered on Apr 27, 2020 | 1,710 views


I had the same problem. I pressed the "Start Cancel" button, kept it down, then pressed "Rinse Only" button. The display then went clear. I pressed "Start Cancel" again, then "83" showed up on the display. I let it run its cycle, then it corrected itself. A little scary, but it worked. This answer board is great!

Frigidaire 24... | Answered on Apr 22, 2020 | 30,344 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18342 Answers

Cindy Wells

Level 3 Expert

6100 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...