Frigidaire Logo

Frigidaire Recent Questions, Troubleshooting Help & Support

  • 3K Products
  • 134K Answers

Press the check filter light on the actual unit.

Frigidaire... • Answered Yesterday

I had the same problem. I pressed the "Start Cancel" button, kept it down, then pressed "Rinse Only" button. The display then went clear. I pressed "Start Cancel" again, then "83" showed up on the display. I let it run its cycle, then it corrected itself. A little scary, but it worked. This answer board is great!

Frigidaire 24... • Answered on Jun 15, 2021

Good Afternoon Sammy, thank you for your inquiry!

Based off the information you have provided you would like to reset your Frigidaire dishwasher because it is flashing "ER". The best way to reset your dishwasher is to flip the household circuit breaker off for roughly ten minutes. If you continue to receive the "ER" code it could be a possible problem with your main control board or keypad. I hope this is helpful information. -Matt

Frigidaire... • Answered on Jun 15, 2021

sad to tell you but only a local repair service will be able to figure it out for you

Frigidaire... • Answered on Jun 06, 2021

So I just had this happen with my Frigidaire fad704dwd dehumidifier. I went to basement and heard it running and sounded off. The compressor was running fan was off which is bad and humidity said 30. I then pushed the off button and it stayed running. I was able to fix it. To make long story short it was a bad ground. I took the plastic back, sides, and front off. There was a green ground (main ground) and Green/yellow ground (fan ground) on the front coil with a bunch of rust. Removed the grounds connected them both together and cleaned the surface area and used a new stainless screw nut and screw to remount the wires to evaporator coil. Everything started working fine after that and I put it back together. Good Luck

Frigidaire a/c... • Answered on Jun 05, 2021

Hello friend, thank you for your inquiry!

From the information you have provided you are experiencing black soot on your Frigidaire stove top. This could be items from your pan or pot falling and being burnt by the elements. You may also want to inspect the area around the stove to assure nothing is falling onto the elements. If you need further assistance please comment back and I would be happy to help you. -Matt

Frigidaire... • Answered on May 30, 2021

if some light weight oil will not work then you have no option but to buy a new stove .I would try silicon lube first

Frigidaire Ovens • Answered on May 28, 2021

This indicates it is the High Limit Thermostat, which isn't a fuse. Most dryers have three heat related components. They usually trip because of bad airflow, check the hose at the back and the vent in the wall. This is the time that birds make nests in them! Also wash the lint filter with dish soap and a brush. Part No. 33 here The error code of E65 is a high limit thermostat trip . For Electric Model, check Inlet Thermal Limiter for continuity. If Thermal Limiter is open, check for evidence of high temperature event and any resulting damage. If no further damage is evident, replace Thermal Limiter. Jul. 27, 2017

Frigidaire dryer still codes E65 after an E64. Replaced heater ... > ... > Dryer Vent Problems

Frigidaire... • Answered on May 27, 2021


Here is the error information for Fault Code F7

F7 Lock motor relay watchdog circuit is active when it should be off Microprocessor checking the operation of the EDC lock, relay failed. Replace EDC.
Hope this is helpful, I will also provide you a link to to a helpful site.

Frigidaire... • Answered on May 24, 2021

is the fan running ion the freezer is the compersser runing and the cond fan >??

Frigidaire... • Answered on May 24, 2021

It is a warning that the fridge thinks the defrost heater is bad Frigidaire side by side Model Ffhs2622msu Flashing H on the... H means that the refrigerator thinks the heater is bad. You'll need to pull everything out of the freezer and remove the back panel inside the freezer. You'll see the silver evaporator coils with the evaporator fan above it. Apr. 14, 2020

What does flashing h mean on Frigidaire refrigerator?

Frigidaire... • Answered on May 24, 2021

Check and clean/clear bottom drain screen if have one pump operating properly and main drain line for clogging

Frigidaire... • Answered on May 13, 2021

Good Afternoon Friend, I understand that your Frigidaire Affinity washer, model# ATF705BZHS, is not filling with water and showing an E11 error code. The E11 code means that your washer is taking a long time to fill. First, make sure that the incoming water faucets are turned on. Next, you will want to make sure that the pressure is above 30 PSI. I suggest resetting your washer, by either unplugging it or shutting the power off at your home's circuit breaker for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful. -Best Regards- WP

Frigidaire... • Answered on May 09, 2021

That's a great question, friend!

I see you question is labeled under model FGES3065KB. In order to remove the drawer on that specific Frigidaire range you would need to follow these steps:

1. Open the drawer to full position.

2. Locate the latches on both sides of the drawer.

3. Pull up on the left glide latch and push down on the right glide latch.

4. Pull the drawer away from your range.

I hope this information is helpful to you. -Matt

Frigidaire... • Answered on May 05, 2021

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Brad Brown

Level 3 Expert

18690 Answers

Cindy Wells

Level 3 Expert

6281 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides