Frigidaire Washing Machines - Recent Questions, Troubleshooting & Support


either belt loose or agitator cogs under agitator bad

Frigidaire... • Answered 14 hours ago


Check and clean/clear bottom drain screen if have one pump operating properly and main drain line for clogging

Frigidaire... • Answered on May 13, 2021


Good Afternoon Friend, I understand that your Frigidaire Affinity washer, model# ATF705BZHS, is not filling with water and showing an E11 error code. The E11 code means that your washer is taking a long time to fill. First, make sure that the incoming water faucets are turned on. Next, you will want to make sure that the pressure is above 30 PSI. I suggest resetting your washer, by either unplugging it or shutting the power off at your home's circuit breaker for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful. -Best Regards- WP

Frigidaire... • Answered on May 09, 2021


No model number stated. R134a is the type of refrigerant used!

Frigidaire... • Answered on Mar 12, 2021


Defective pump or leaky connecting lines

Frigidaire... • Answered on Feb 28, 2021


The Frigidaire Affinity Washer Error E41 is a door lock error. It means the primary control thinks the door is open. If the door is closed and this error persists, then in most cases, you will need to replace the door lock assembly on the washer. Sometimes this error can be caused by the control board, but it's more common for the door lock assembly to have failed than the control board.

Frigidaire... • Answered on Feb 14, 2021


solenoid valve is probably faulty, it is usualy located at the top of the machine close to the drawer

Frigidaire... • Answered on Jan 22, 2021


Hello 2cats - First, is the drain pump making a humming noise? If so, the unit could possibly have a restriction in the drain line. Try setting the cycle to spin only and verify if water pumps out. Other possibilities could be a faulty door lock, timer, pump, or control board not communicating correctly. In this case I would contact a professional to move forward accurately to properly diagnose and repair the washer.

Frigidaire... • Answered on Dec 24, 2020


Hi,

Problems with a washing machine not spinning or not draining are often interrelated..

If you are having a problem with your top load washer then check out thistip...

Washing Machine does not Pump or Spin


If you are having problems with your front load washing machine then checkoutthis tip...

Front Load Washing machine not draining and or not spinning


heatman101

Frigidaire... • Answered on Dec 24, 2020


Just follow these steps:

1. Remove the center dispenser from the top of the agitator. It should just pop off.
2. Locate the white plastic cap underneath and pull straight up to remove.
3. Locate the agitator bolt underneath and remove using a socket and ratchet (can't remember the size). Hold the agitator still with one hand in order to loosen the bolt.
4. With the bolt removed, grasp the agitator by the bottom flanges and pull straight up. It should lift off the center post.

NOTE: Sometimes these agitators will stick due to years of detergent accumulation. You may have to wobble it back and forth to get it loose.

If you have questions, please let me know. I hope this helps you.

Frigidaire... • Answered on Dec 23, 2020


If it beeps during the fill cycle it is possible that there is not enough water going into the machine. Turn the water off and where the hose goes into the machine, there is a bowl shaped gauze screen and a sealing washer. The gauze may be blocked with debris or limescale. Clean with a brush and soak in vinegar or CLR. Also test the tap to the hose by having someone hold the hose in a bucket, whilst you turn the water on. https://www.amazon.ca/LiXiongBao-Stainless-Coupling-Strainer-Connector/dp/B086J4L47D/ref=asc_df_B086J4L47D/?tag=googleshopc0c-20&linkCode=df0&hvadid=459590544144&hvpos=&hvnetw=g&hvrand=2862470894891564456&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9000809&hvtargid=pla-945096412703&psc=1 ..

Frigidaire... • Answered on Dec 08, 2020


If you house water pressure seems normal check the following pressure switch, lid switch and the water inlet valve. Also check for any blockages in the water lines check the water screen where the water lines hook into the wash clean screen with toothbrush and soap .

Frigidaire... • Answered on Nov 28, 2020


Frigidaire Washer/Dryer Combo: Model GCET1031FS2 Parts ...

www.repairclinic.com > ProductDetail
Frigidaire Washer/Dryer Combo Model GCET1031FS2 Parts. Frigidaire ... If the dryer overheats, the thermal fuse blows to cut off power to the dryer. If the thermal ... ..

Frigidaire... • Answered on Nov 12, 2020

Not finding what you are looking for?
Frigidaire Logo

11,089 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...