Frigidaire Kitchen Ranges - Recent Questions, Troubleshooting & Support


Connie P, Unfortunately it is not possible to make the display brighter. The only solution is to replace the entire clock/timer. The price for the part is less then a hundred dollars and if you will give me the complete model number and a color, I can help you to find the best deal. Gendos...post back

Frigidaire... | Answered on May 10, 2020


Sounds like a problem in the oven control board, something not easy to test. That said, I don't find your model number. It would have been helpful to know the error code, something you didn't supply. You might repost a query with the error code and the model number.

Sometimes a reset can be achieved by simply shutting off a circuit breaker and then closing it again. Or, the bottom panel of an oven might slide out give you access to a plug if the oven is not hardwired to your living quarters. But if the stove comes back to life sporting the same error message, I suspect you are destined to access a repairman or a new stove. Still, you might get some information below. Sorry, without the model number and error code, there is not much more I can determine about this.

If your stove is under warranty, the following may be of assistance.

https://www.repairclinic.com/RepairHelp/Range-Stove-Oven-Repair/13-2--/Frigidaire-Range-Stove-Oven-Troubleshooting

Frigidaire... | Answered on Apr 02, 2020


Hi,

The F10 F11 F12 F13 F14 Error Codes indicate that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You would need to access the electronic oven control board (Timer) in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem.


http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Thanks to blueextc3221 for this solution.

Frigidaire... | Answered on Jan 09, 2020


You may still have a bad Electronic Range Control (ERC). This is your timer that you mentioned. The oven is controlled by the ERC. There is a separate circuit for the BROIL and BAKE functions. Does the BROIL element still work? Or, are both elements not working? You may want to double check all your connections from the element to the control board as well. Sometimes the wire lugs can oxidize and not make good contact. Check the ERC to see if there any obvious signs of failure. Burned components are common. These boards are considered "non-serviceable" and usually requires replacing. You can attempt component-level troubleshooting if you are savvy with electronics. There's usually a basic block diagram that comes with your appliance mounted somewhere inside the operator console or on the back panel of the range.

The ERC for your range would cost in the neighborhood of about $100 - $140 to replace. Prices will vary between model versions and will also depend on where you get it. It is a very simple repair job if you wish to pursue this yourself. I can give you step-by-step instructions if you need further assistance. I hope this helps you.

PS The reason all your surface elements still work is because they are controlled by infinite switches behind the control knobs. There is a separate switch for EACH burner.

Frigidaire... | Answered on Dec 23, 2019


My range doesn’t allow me to set the time, when I enter the current time it flashes and then defaults to 2:22.

Frigidaire... | Answered on Dec 12, 2019


Hi Junior-
I found this youtube video on resetting f10 code on a gas stove.
https://www.youtube.com/watch?v=z6tcnpDKDns

Hope this helps.

Frigidaire... | Answered on Nov 28, 2019


Due to the cost of parts on this range, I would call an engineer. $310 for the oven control board, $400 for the 2 elements.

The only thing I would suggest is checking the contacts at the back of the back panel. you must have checked the element contacts when you did the continuity test. I have seen contacts get hot and snap off.

https://www.partselect.ca/Models/LGEF3045KFK/Sections/Backguard/?ModelID=6747678&ModelNum=LGEF3045KFK&mfgModelNum=&ManufactureID=4&Selected=BA2790DC09E1C5239A8B7CD13A1069F3169E482E&Position=1&mfg=Frigidaire&Type=Washer&Mark=1

Frigidaire... | Answered on Aug 13, 2019


Dear IFE KIARA,
Warning: If you feel in any way uncomfortable/unsafe performing this test or making this repair, please contact a qualified appliance repair technician.

F13 error is related to the clock. this error can occur when the clock looses communication between the keypad or any of the sensor in the stove, including the heat probe. sometimes resetting the power will fix the problem.
Try disconnecting power to the stove completely and flip the corresponding breaker on and off at the breaker box.
Wait 30 seconds and then turn everything back on.
if the problem persist after power-up, according to Frigidaire suggested corrective action the electronic oven control,also called EOC has to be replaced. Here is a search link from Google for the part in question.

Best of Luck,
JP
https://www.google.com/search?source=hp&ei=fecFXYCMAsKr5wKBm6G4DQ&q=316418735&oq=&gs_l=psy-ab.1.0.35i39l10.0.0..5525...1.0..0.209.209.2-1......0......gws-wiz.....10.8VUU1xaL8qM

Frigidaire... | Answered on Jun 16, 2019


Hi im an appliance tech and i had the same problem its not the EOC other words control board its actually the speed bake swith its stuck in the on position that why you get a stock keypad error code either f1 or f11 replace that switch or disconnect it and im positive that this will solve it .

Frigidaire... | Answered on Jun 13, 2019


As copied from the manual.

Setting a silent control panel
When choosing a function, a beep will be heard each time a pad is pressed. If desired, the control can be programmed for silent operation. Press and hold (start/time) . After 7 seconds, the control will beep once. This will block the controls from sounding when a pad is pressed. To return the sound, press and hold (start/time) again for 7 seconds until the control beeps once

NOTE!
The OVEN indicator light on the electronic display will turn ON and OFF when using the Bake feature and during preheat. This is normal and indicates that the oven is cycling to maintain the selected baking temperature. When the preheat indicator light turns OFF, your oven is ready.

Frigidaire... | Answered on Jun 05, 2019

Not finding what you are looking for?
Frigidaire Logo

3,111 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Kitchen Ranges Experts

Ismael Rodriguez...

Level 2 Expert

184 Answers

Paul Carew

Level 3 Expert

3510 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Frigidaire Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...