E000025 0200 this error code e000025 0200 always show after i print 1 or 2 pages. this all started when i changed the cyan toner pls pls help

Konica-Minolta bizhub C253 - Error Code - Printcopy.info

https://printcopy.info > code=C2552
Code: C2552 · Description: Abnormally high toner density detected cyan TCR sensor TC ratio in the developing machine, which is determined by Toner replenishing ...

• 
  

  Konica-Minolta bizhub C220 - C2552 - PrintCopy .info

  https://printcopy.info > code=C2552
  Code: C2552; Description: Abnormally high toner density detected cyan TCR sensor • TC ratio in the developing unit which is determined by toner replenishing ...
  
  and a video
  
  https://www.google.com/search?q=error+code+c2552+in+konica+minolta+C253
  
  ..

Take the cyan image unit out, clean the contacts on the chip remove any oil from your and interfering with the electrical contacts. Is the toner cartridge Third party or OEM??? if third party get a OEM. Sure it does not say Cyan Image Unit not Toner Cartridge?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Generic toners often cause this error. Was the cyan you purchased a aftermarket compatible?

Just because they are new toners, doesn't mean they can't be faulty.

Faults that show in just a single colour are almost always related to THAT colour toner cartridge.

TRY THIS

If you still have your old cyan toner, swap the chip from your new toner and put the old toner in the printer, then test.

If the lines are gone, it's the NEW cyan toner cartridge.

7002 is the error code; 0006904 is the printer page count.

Error means-

Toner motor 2 overcurrent detection error (cyan toner)

• The engine controller PWB (A0004)

detected the overcurrent of toner
motor 2.

Possable causes-
1. Lump of toner inside cyan toner container or defectiveness of toner replenishment drive system.
Replace the cyan toner container.
2. Defective toner motor 2.
Replace the toner motor 2.
3. Defective engine controller PWB (A0004).
Replace the engine controller PWB (A0004).

Check to see if you waste toner recycling for the cyan is working or being blocked. Check the transfer bias roller next to the cyan drum. Return you cyan imaging unit for a warranty replacement. Check for obstructions to the cyan developing unit. Check that the cyan IU was put into the machine properly. Check for toner leaking from the entrance to the developing unit or from the toner cartridge.

or, call a qualified KonicaMinolta tech to check out and service your machine.

Hi,

Please follow the solution in the link below. Also as you putting in the cartridge always check for loose toner in the area and on the cartridge itself as this can block the sensors.

http://www.support.xerox.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=74,E=0000000001343666831,K=8485,Sxi=0,Case=obj(3510)

Niallbt

First off, this is a comment from a random person who may or may not know ALOT about these printers and toner/printer design in general. All toners are not designed to the same specification. Toner is a combination of plastic "pigment" and iron like shavings to make it magentically attracted to the electrical charges within the unit. Different toners conform to different grades and mainly size of the particles within the blend. The manufacturer doesnt only recommend that you use their toner to make them money, yes of course it makes money, but its because when the unit is designed it is designed to use a certain grade of toner, trust me if you put the non-branded toner vs the branded toner under a microscope you would see quite a difference. Often the non-branded toner is much larger in particle size (obviousely because its cheaper to make at this spec). This causes a variety of issues from excess toner not being cleaned off of developer rollers, IDT rollers, or clogging of toner dispenser tubes in the unit and the micro filters contained at the toner dispenser assy and developer assys. Also as for the issue not changing when switching to dell branded toner - the dispenser tubes within this unit contain up to 500-1000 pages worth of toner, making no change in toner you make immediately visible. Also depending on the damage caused by the previous toner, it may not be able to be fixed until all the components in between the toner and final delivery (drum cart) are replaced. In this case more than likely the toner dispenser assy, all developer assy's, and drum cartridge need to be replaced, and than be sure to stick with factory branded toner :)

It is the developer. All colours should be changed at the same time. This can be accessed via the right hand side of the machine, when you remove the cover. (where the output tray is)

I had the same problem and found that one of the toner cartridges must have not been seated properly. I removed the black toner cartridge and re-fitted it. The printer now works fine again with no errors. 17H is a code relating to a fault in the rotation ......... possibly one or more toner cartridges need checking. Use the menu on the printer to turn it to the appropriate position (i.e. engine menu then select replacement of whichever toner you are checking).
Hope this fixes your as well.
Chris