20 Most Recent
Pioneer VSX-D307 Receiver - Page 4 Questions & Answers
Slow playing pioneer phonograph pl-202az
most record players use a rubber wheel against the turntable (on the inside) to turn it.. as they get old and brittle they tend to slip a lot. a temporary fix involves cleaning the rubber piece but it really needs replacing..
Pioneer VSA-5500 can switch on but no display and sound
It sounds like you are having an issue with your Pioneer VSA-5500 receiver not displaying or producing any sound. It's likely that the problem is related to a malfunctioning main control board or a power supply issue. Here are a few things you can try:
- Check all the connections between the main control board, power supply, and other components to ensure that they are properly connected and not loose.
- Check the fuse on the power supply board, make sure it's not blown, if it is, replace it with a new one.
- Check the voltage on the power supply board, make sure the voltage is correct, if the voltage is too low or too high, the main control board may not be receiving enough power to function.
- Check the power supply board for any signs of damage, such as burn marks or leakage, if the power supply board is damaged, it will need to be replaced.
- Check the main control board for any signs of damage, such as burn marks or leakage, if the main control board is damaged, it will need to be replaced.
- If none of the above steps resolve the issue, it's likely that the problem is with another component in the receiver and it will require further diagnosis by a professional technician.
It's important to note that troubleshooting and repairing electronic equipment can be dangerous, especially if you're not familiar with the device, so it's best to contact a professional technician if you're not comfortable working with it.
How to factory reset a pioneer VSX-d508
To factory reset your Pioneer VSX-D508 audio receiver, you will need to follow these steps:
Turn off the receiver.
Press and hold the "Tone" and "Speaker A" buttons on the front panel of the receiver.
While holding these buttons, turn the power back on.
When the display shows "Initialize," release the buttons.
The receiver will now begin the factory reset process. When it is finished, the display will show "Completed."
Turn the receiver off and then back on again to complete the reset.
Keep in mind that this process will reset all of the settings on your receiver to their default values. You will need to reconfigure any settings that you have changed since you purchased the receiver.
Why can I get no sounds for my vintage vsx 5600 pioneer home theater system
There could be a few reasons why you are not getting any sound from your vintage VSX 5600 Pioneer home theater system. Here are some things you can try:
- Check the connections: Make sure all of the cables are securely connected to the appropriate ports.
- Check the power: Make sure the home theater system is turned on and the power cord is plugged in.
- Check the volume: Make sure the volume on the home theater system and the volume on your TV are turned up.
- Check the input: Make sure the home theater system is set to the correct input.
- Check the speakers: Make sure the speakers are turned on and properly connected.
How to reset Pioneer VSX-AX3 with no power?
It is not recommended to attempt to reset a device with no power. If the power is off, the device will not be able to respond to any commands or perform any actions.
If your Pioneer VSX-AX3 is not turning on or functioning properly, there are a few things you can try before attempting to reset it:
- Make sure the device is properly plugged in and that the outlet is functioning properly.
- Check the power cord for any damage, such as frayed wires or loose connections.
- If the device is connected to a surge protector or power strip, try plugging it directly into a wall outlet.
- Try a different power cord or outlet to eliminate the possibility of a problem with the cord or outlet.
If none of these steps help, you may need to have the device repaired or replaced.
How do I hook up Kenwood gge 7030 to my pioneer sx217?
To connect a Kenwood GE 7030 equalizer to a Pioneer SX-217 receiver, you will need to use the tape record out and in jacks on the back of the receiver. Here is a general outline of the steps you can follow to set up the connection:
Locate the tape record out and in jacks on the back of the receiver. These are typically labeled "TAPE MONITOR OUT" and "TAPE MONITOR IN."
Locate the tape in and out jacks on the back of the equalizer. These are typically labeled "TAPE IN" and "TAPE OUT."
Use a pair of RCA cables to connect the tape out jack on the receiver to the tape in jack on the equalizer.
Use another pair of RCA cables to connect the tape out jack on the equalizer to the tape in jack on the receiver.
Turn on the equalizer and set the volume and tone controls to your desired settings.
Turn on the receiver and select the tape monitor function. You should now be able to hear sound through the speakers.
If you are still having trouble getting the equalizer to work, it is possible that there is an issue with the cables or with one of the components. You may want to try using different cables or checking for any visible signs of damage on the components. If you are still having trouble, it may be helpful to consult the user manual for the receiver or the equalizer or to seek the assistance of a professional audio technician.
Pioneer vsx 405 is a muting there's no sound
Hi,
Please check that the mute button on the device or any associated remote control is not stuck in the down/pressed position. If not, then please switch the sound source and test the device for sound again. Otherwise, we can move onto a power cycle of the device.
Thank you.
How can I get rid of the FL OFF blue blinking light on Pioneer VSX-90 receiver?
FL OFF could indicate a problem with the power supply or the cooling fan inside the receiver. Try unplugging the unit to reset the error code. If the error persists, the receiver needs to be serviced. If the Pioneer VSX-90 is still under warranty (1 year), contact the manufacturer. Otherwise, decide if it is worth fixing (including the shipping costs and minimum service fee).
I wish that I had better news for you. (There are service manuals available for sale online. I know nothing about these vendors.)
Cindy Wells
How do I get my new LG OLED 65C1PU TV to play through my old Pioneer VSX-D507S surround system?
Old technology and new technology often don't mix. Your television is new and geared up for Bluetooth and HDMI, your old surround sound system is composite video and audio. You need to test the television with something else, and then check the surround sound with a different input. If they both work then you know it is a compatibility issue. Your best bet is a new Bluetooth Sound Bar that is as good as the television.A similar issue was posted here yesterday, so you are not alone.https://www.fixya.com/support/t29896811-jvc_rx_6018v_not_working_tv..
No optical light from pioneer vsx516
Hi,
Please double check that you've adjust the volume on the speaker and test sound with multiple sources (ie CDs, DVDs etc) to ensure that the volume/sound issue is cause by the speaker and not the item that it's attempting to play.
You can also check for any disconnected wires going from or to the speaker. Thank you.
Pioneer PDR-609 CD Recorder. -
I don't have a stand-alone cd recorder but like many people I have burned discs on the computer and had many disappointments. While some disc drives are clearly better than others, for no apparent reason, there does seem to be more reject discs with some software than others.
Particularly disappointing is the Nero burning software that performs well when it is first installed but seems to deteriorate fairly quickly with every computer restart. I know nothing about such things so I am only guessing the cause might be that Nero displaces some Windows components and Windows seems to try repairing itself when booting.
Like most things these days, especially digital things, your cd recorder is in fact a computer that depends entirely on the software loaded into it, software that could degrade or become corrupted over time.
While it is possible the disc drive (laser perhaps) has become less potent it wouldn't be unreasonable to suspect the software and I suggest you contact Panasonic.
It is probable, like many things requiring software, early versions were found to have problems and would be periodically updated.
Not finding what you are looking for?