I need a new battery for this razor. I know its replaceable, but where dose it go and how do you get the cover off?

Hi Docle60,
You'll only need a couple of tools and a little time. The steps are pretty easy.

• Take your electric razor apart to find out what type of replacement battery you need.
• Buy your replacement batteries.
• Remove your old batteries
• Solder the new batteries and place.
• Reassemble your razor and test it.

There are a couple of ways to buy your replacement batteries.

• Do a google search using the model number of your razor.
• Find the original battery model number and search using that
• Find the original battery voltage and milliamps and search using that information.

Using the model of your razor, you might want to try shavers.com or, If your not good at soldering, purchase pre-tabbed batteries already soldered on them. If your batteries are a standard size, you can purchase them from Amazon at a reasonable price.

Hop this helps
David

Follow the wires from the battery all the way to the motor. You should find a large amp sized fuse or a resettable circuit breaker in line. Razor PR200 24V Electric Motorbike Parts

Do you own a multimeter to check the voltage output from the battery

You threw away a perfect scooter you idi0t. Needed to desulfate battery with a smart charger. M0ron.

The battery installation guide is available here
http://www.razorama.com/razor-installation-guides.html

It shows how to remove the covers.

Razor E100 batteries are easily replaced & there are guides on how to this on razor.com, genuine Razor batteries are available at most good Razor product stockists.

It is doubtful that the cord is the problem unless there is visable damage to the cord. Most likely, the batteries are dead. You will find the correct replacement battery type at shaveroutlet.com. See link below. You will need 2

http://shaveroutlet.com/shaver-replacement-parts/batteries/shaver-battery-pack-for-most-shavers-p-211.html

To change them, take off the back cover by removing the screws. Inside you will see the two batteries. There may be some black tape on the ends. If so remove the tape so that you can get to the tabs on the batteries. Unsolder the old batteries from the wires and solder in the new batteries

If you are not equipped to do this yourself, shaveroutlet.com can do it for you. See link below for information and ordering

http://shaveroutlet.com/shaver-replacement-parts/professional-battery-replacement-for-most-models-p-374.html

It sounds like the battery pack needs replaced. You will find the correct battery type at shaveroutlet.com. See link below. You will need to order 2 batteries

http://shaveroutlet.com/shaver-replacement-parts/shaver-replacement-battery-aa-nimh-p-108.html

To replace, you will need to remove the back cocer by removing the two screws. Take off back cover to access inside. For easier replacement, it is sometimes suggested that you use a modified installation technique. This is to break the tabs off of the old batteries rather than unsoldering them from the circuit board. This allows the old batteries to be removed but leaves the tabs attached to the circuit board. You can then solder the tabs from the new batteries to the old existing tabs

There are two round screw covers on the bottom. Pry these out to reveal two screws. Remove screws and then the out case can be slid downward and off. You can then access the batteries

Replacement batteries for model 5614 can be found at shaveroutlet.com. See link below

http://shaveroutlet.com/braun-battery-nimh-2-batteries-p-105.html

You will find batteries at shaveroutlet.com. See link below

http://shaveroutlet.com/shaver-replacement-battery-aa-nimh-p-108.html


To open the shaver body, you will first need to gently pry off the 'cap' on the bottom that surrounds the hole where the cord plugs in. Once removed the side grips will pull off revealing 4 screws. Remove screws to take off back cover and access insides. Inner parts simply lift out. Reassemble in reverse order