Answered Hayward 1 12 Hp Super Swimming Pool Pump Sp2610x15 Questions & Issues Page 8

1 Answer

What does this mean Hayward pool heater h150FDN gives us an hs or h5 error?

HS = High Limit Sensor
Heaters Maximum Water Temperature has been Exceeded.
A few reasons this occurs...

Low water flow thru heater, check :
- Dirty Filter
- Opened By Pass Valves
- Plugged pump impeller
- Dirty/Full baskets at skimmer or pump
- Anything that may reduce water flow
Sensor could actually be doing its job, in a different aspect, Thermostat failure, and water is overheating in spa or pool?

But anyway, your heaters fault code you asked about is: hs, not h5

Hayward Pool &... | Answered on Jun 15, 2015 | 459 views

2 Answers

My hayward swimpro abg100 powers on but nothing happens. I can hear a buzz coming from it but it does not ignite or anything. What can I do?

Warranty status? Probably gas control valve and its connections to the "buzz" ignitor system. Gas is not a DIY thing!

Hayward Pool &... | Answered on Jun 09, 2015 | 297 views

1 Answer

Need to know how much cand to use for a hayward modle 711

You need to be specific, with correct information.
I would be glad to assist, once we know what size filter you have?
What you provided was the model number of the multi port valve. No help at all at determining size of filter!

Hayward Pool &... | Answered on May 31, 2015 | 61 views

1 Answer

Video how to clean copper jets in pool heater

Might you be referring to the Brass Gas Orifices?
a 'Stripped' #12 gauge copper wire works great!
Bend it into something like a lambs hook, yes- like Mary Had A Little Lamb...
then poke and clean out.
If needing a more thorough job, each one does unscrew from the gas manifold.

Hayward Pool &... | Answered on May 29, 2015 | 107 views

1 Answer

Hayward sp1592 keeps smoking and shutting off. Is there a repair or cheaper to buy new one. 10 years old

Not worth the repair...
get a new one.

Hayward Pool &... | Answered on May 29, 2015 | 45 views

1 Answer

Lose press on retrn to pool using Hayward S166t with brand new veri flow pump attached. I back wash and pressure restored is excellent but within 15 or twenty min drops off again.

what is the water like?
Dirty? Green? Murky? Cloudy?
Something is clogging the filter!

Let me ask this, you said: "Pressure drops Off" ???
Do you have a pressure guage on the filter?
Does the pressure increase? Or does it Decrease?
This will be an important piece of information!!!!

If pressure increases on the pressure gauge...
- then filter is working and filtering out dirt and filter is clogging up.
If pressure decreases on the filters pressure gauge,
- then the basket, or literally anything that is decreasing or stopping the water from getting to the pump, or more precisely to the internal impeller of the pump!

Most commonly - plugged impeller, baskets need to be checked, enough water in pool? etc.

Hayward Pool &... | Answered on May 26, 2015 | 241 views

2 Answers

What is a 1F code on the hayward pool heater

The code you are referring to is actually IF, not 1F. It stands for ignition failure.
If the control exceeds the maximum number of ignition retries or recycles the heater will shut down and go into lockout. Automatic reset is 60 minutes.

Hayward Pool &... | Answered on May 25, 2015 | 7,467 views

1 Answer

Lo error on hayward pool heater

"LO" is simply informing you that the Heater is not sensing proper water flow through it! A Flow Problem.
A special sensor, called a pressure switch is this source. But... That does not mean it is bad - No, it is in most cases just doing its job!
Most common reason - Dirty Filter.
A good cleaning of the cartridges, or maybe a breakdown and recharge of a DE Filter, or a good cleansing backwash of your sand filter, will remedy this situation.
Or... Check for any OTHER reason or situations water flow may be reduced through the heater:

enough water in pool or spa?
If you have a weir gate in skimmer, is it stuck in the UP position?
Are any valves closed?
Do you have a bypass valve at the heater?
- If open, this will reduce the amount of water going thru heater, close it to the point, LO goes away.
Could be debris in front of Pressure Switch, in the copper tubing
- Unscrew and remove pressure switch, turn pump on. But first, align end of tube so that when water squirts out it will shoot out from heater and not onto electronic heater components!
If all above is good, you may have failed pressure switch?
Etc

Good Luck - hope this helped.

Hayward Pool &... | Answered on May 25, 2015 | 99 views

1 Answer

Hayward propane pool heater service light on Lo 60 message

"LO" is simply informing you that the Heater is not sensing proper water flow through it! A Flow Problem.
A special sensor, called a pressure switch is this source. But... That does not mean it is bad - No, it is in most cases just doing its job!
Most common reason - Dirty Filter.
A good cleaning of the cartridges, or maybe a breakdown and recharge of a DE Filter, or a good cleansing backwash of your sand filter, will remedy this situation.
Or... Check for any OTHER reason or situations water flow may be reduced through the heater:

enough water in pool or spa?
If you have a weir gate in skimmer, is it stuck in the UP position?
Are any valves closed?
Do you have a bypass valve at the heater?
- If open, this will reduce the amount of water going thru heater, close it to the point, LO goes away.
Etc

Also, on a propane heater, some makes & models will have the gas valve 'Lock Out'. This will be done by the ignition control module. To reset, heater will need to be powered off, then back on. Good Luck - hope this helped.

Hayward Pool &... | Answered on May 25, 2015 | 70 views

1 Answer

Hayward stratum won't start pump. It says ac voltage too high. How do I trouble shoot it? I think it is getting 240 volts.

Make sure the voltage is set for 240 volts and not 120 volts

Hayward Pool &... | Answered on May 15, 2015 | 102 views

1 Answer

What size is the drain plug on my Hayward pool pump s166t

Most Pool Pumps use a 1/4" regular standard thread.
Thats pretty standard.
Now the filters from Hayward vary! They use a cap normally, and size is all over the board.

Hayward Pool &... | Answered on May 11, 2015 | 92 views

1 Answer

I have a part leaking on the inside (right behind the front panel). there is a blue & red wire coming from it. "21-99" is written on top of it. I don't see this part in the manual. can you help

Pressure switch.

Hayward Pool &... | Answered on Apr 22, 2015 | 118 views

2 Answers

How do you replace an air relief valve on Hayward filter pump?

https://www.hayward-pool.com/shop/en/pools/manuals

Manuals Pools

Hayward Pool &... | Answered on Apr 21, 2015 | 224 views

1 Answer

How to set temperature

Turn dial or press the up /down button to desired temp

Hayward Pool &... | Answered on Apr 04, 2015 | 54 views

1 Answer

Hayward 100 pool heater shaking

Not enough water flow!
Either a

bypass valve is open all the way, and reducing water flow into heater
Worn/broken internal bypass - unitherm governor
Blockage of some sort reducing water flow, in circulation line

When something like the above is present, the minimal water flow, gets super heated really fast when heater is on and firing! So hot in fact, that the water turns to Steam Instantly!
and the steam is a very Volatile substance! Remember? It was once used to move Locomotives!
get this fixed asap!
call a pool / spa professional for assistance in evaluating your next step.

Good Luck.

Hayward Pool &... | Answered on Apr 04, 2015 | 311 views

1 Answer

SP34000VSP "CHECK SYSTEM" LIGHT COMES ON (SOLID, NOT BLINKING). IS THERE A COMMON PROBLEM CAUSING THIS?

Dirty filter? Possible flow problem?

Hayward Pool &... | Answered on Mar 11, 2015 | 84 views

2 Answers

My hose is collapsing when i use my pool cleaner

the filter is clogged up which needs to be cleaned
I don't know if you you have a sand filter or an earth filter system but get it cleaned to operate correctly

Hayward Pool &... | Answered on Dec 18, 2014 | 5,015 views

1 Answer

Heater comes on but dont heat the hot tub what could be wrong

120 or 240 spa?

how long does the heater stay on?
how do you know the heater even comes on?

Try cleaning the filter, then check.

Hayward Pool &... | Answered on Nov 01, 2014 | 90 views

1 Answer

My Hayward heatpump will no start up the fan works but no compressor I cleaned the evaporator reset circuit breaker and still no start

check the startup capacitor to the compressor

Hayward Pool &... | Answered on Oct 23, 2014 | 56 views

1 Answer

My hayward heater (brand New) keeps going into IF mode Why

IF means ignition failure make sure gas supply is correct pressure make sure heater is wired correctly usually if wired 120 volt you have to change wiring to accomidate that voltage if wired correctly and is 120 volt reverse black and white wires

Hayward Pool &... | Answered on Oct 05, 2014 | 66 views

Hayward 1 12 Hp Super Swimming Pool Pump Sp2610x15 - Page 8 - Answered Questions & Fixed issues

What does this mean Hayward pool heater h150FDN gives us an hs or h5 error?

My hayward swimpro abg100 powers on but nothing happens. I can hear a buzz coming from it but it does not ignite or anything. What can I do?

Need to know how much cand to use for a hayward modle 711

Video how to clean copper jets in pool heater

Hayward sp1592 keeps smoking and shutting off. Is there a repair or cheaper to buy new one. 10 years old

Lose press on retrn to pool using Hayward S166t with brand new veri flow pump attached. I back wash and pressure restored is excellent but within 15 or twenty min drops off again.

What is a 1F code on the hayward pool heater

Lo error on hayward pool heater

Hayward propane pool heater service light on Lo 60 message

Hayward stratum won't start pump. It says ac voltage too high. How do I trouble shoot it? I think it is getting 240 volts.

What size is the drain plug on my Hayward pool pump s166t

I have a part leaking on the inside (right behind the front panel). there is a blue & red wire coming from it. "21-99" is written on top of it. I don't see this part in the manual. can you help

How do you replace an air relief valve on Hayward filter pump?

How to set temperature

Hayward 100 pool heater shaking

SP34000VSP "CHECK SYSTEM" LIGHT COMES ON (SOLID, NOT BLINKING). IS THERE A COMMON PROBLEM CAUSING THIS?

My hose is collapsing when i use my pool cleaner

Heater comes on but dont heat the hot tub what could be wrong

My Hayward heatpump will no start up the fan works but no compressor I cleaned the evaporator reset circuit breaker and still no start

My hayward heater (brand New) keeps going into IF mode Why

Not finding what you are looking for?

Popular Tags

Ask a Question

Popular Products

Hayward SAND FILTER, PRO SERIES

Hayward H-series Electronic Gas Pool Heater H400

Hayward 250kbtu Ng Pool Heater - Inground

Hayward 2HP Pool Pump Motor A O Smith Electric Pool...

Hayward 1.5 Hp Northstar High Performance Pump

Top Hayward Pool & Spa Experts

john h

Marvin

Paul Carew

Are you a Hayward Pool and Spa Expert? Answer questions, earn points and help others

Manuals & User Guides