Red light on 2 arrows and not printing. triangle above ok and 4 colours ok. toner bottle has just been emptied and checked it is back in properly.

Minolta says: http://printcopy.info/?l=en&mod=free&chap=erc&brand=Konica-Minolta&model=bizhub%20215&code=C2558

C-0070 is the toner bottle, remove it, power off the machine, then with the bottle out turn the machine on, let it go thought its routine when it ask for toner install it PROPERLY if the knub on the bottle dented damage in anyway replace do not use the damaged bottle. the C0F32 is the toner is not properly mixing in the the developer because it is not getting any toner see above, Might need to replace the developer also.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

The waste toner bottle is behind a panel on the lower, rear right hand corner of the unit. You have to remove the panel cover with a screwdriver. Empty or replace the bottle. If you empty rather than replace, make sure to clean the sensor window from the inside (stick a ruler with paper towel rubber banded to it in through the top and rub off toner dust). Often the bottle isn't even full, but this sensor window is dirty making the machine think the bottle is full. After replacing/returning the bottle and securing the panel cover back on, login to your unit from the control panel, press the Settings/Registration button (looks like a head with an asterisk inside), then press the 2 & 8 buttons simultaneously, then press the Settings/Registration button again. From here press Mode > Copier > Function > Clear > arrow over to W-TN-CLR > ok. Press yellow button to exit back to main screen. You should be able to print now.

if you found the msg on lcd like "toner empty" & red light near the lcd
then you have to reset toner counter through tech mode.
MENU # 1 9 3 4 MENU pres continues you will find tech mode on lcd
then press 3 times right arrow key "new cartridge" will come on lcd bottom line
then press 2 times ENTER button & swicth of the macine for 5 second then on

all samsung mfds stop printing FAX when "TONER EMPTY" msg comes.

This triangle means that the toner supply is needed. It comes first as a steady triangle meaning toner is running low and eventually flashing triangle which means toner is completely empty and copy cannot run. There are two methods of replacing toner ;
Refilling and cartridge replacing.

• You can refill by opening the waste container and then removing the lid on the unit. Use a sprout provided in Sharp Al1000 toner bottle or improvise by folding a paper into a funnel shape.
• For cartridge , pullout the old cartridge and replace with a Sharp Al100td cartridge.

Nice time.

Hi, this triangle means that the toner is empty. This can also be caused by a defective developer unit drive gears. Check that it is okay if not replace the gears. Replace the toner cartridge or refill the toner in its unit. Make sure you empty the waste on its side as it may cause some noise or toner spills. Use cartridge Sharp Al100td or refill with Sharp Al1000 toner bottle. All the best.

There are actually some certain meaning on the red light and green light showing different information to user. The summaries are:
1) Green On, Red Off = Printer Ready.
2) Green Fast-Flashing, Red Fast-Flashing = Printer warm up.
3) Green Fast-Flashing, Red Off = Printer off-line.
4) Green Slow-Flashing, Red Off = Processing Data.
5) Green Off, Red On = Cover Opened, Toner Empty or Developer Unit / Drum unit missing.
6) Green Off, Red Fast-Flashing = Paper Jam or waiting for jam reset.
7) Green Off, Red Slow-Flashing = Paper Empty or Paper tray is not inserted.
8) Green Off, Red Off = Printer power is off.
9) Green Very-Slow-Flashing, Red Off = Printer in sleep mode.
10) Green (any condition above), Red Slow-Flashing = Toner low or paper empty.

So what is your printer condition? Better know what is going on your printer so can solve the problem

YBC (/\)

You need to enable the cartridge out override:
1. On the control-panel menu, press OK.
2. Use the Left arrow ( ) or the Right arrow ( ) button to select System setup, and then press
OK.
3. Use the Left arrow ( ) or the Right arrow ( ) button to select Print quality, and then press OK.
4. Use the Left arrow ( ) or the Right arrow ( ) button to select Replace supplies, and then press
OK.
5. Select Override out to enable the feature. Select Stop at out to disable it.

There are actually some certain meaning on the red light and green light showing different information to user. The summaries are:
1) Green On, Red Off = Printer Ready.
2) Green Fast-Flashing, Red Fast-Flashing = Printer warm up.
3) Green Fast-Flashing, Red Off = Printer off-line.
4) Green Slow-Flashing, Red Off = Processing Data.
5) Green Off, Red On = Cover Opened, Toner Empty or Developer Unit / Drum unit missing.
6) Green Off, Red Fast-Flashing = Paper Jam or waiting for jam reset.
7) Green Off, Red Slow-Flashing = Paper Empty or Paper tray is not inserted.
8) Green Off, Red Off = Printer power is off.
9) Green Very-Slow-Flashing, Red Off = Printer in sleep mode.
10) Green (any condition above), Red Slow-Flashing = Toner low or paper empty.

So what is your printer condition? Better know what is going on your printer so can solve the problem.

YBC (/\)

If the signs that is blinking red which is shape like triangle , it is the toner cartridge indicator. The toner cartridge is empty.Try to pullout and check the toner cartridge, if it is light in weight it is already empty.