Maytag Control Locked error model # MFW9700SQ1

Make sure there is nothing in the way of the door closing good. Sounds like something keeping it from closing good.

The start button will not operate if the door lock switch is not energised.

Hi.

The model indicated: MDB5651A does not have display and the error codes are shown like flashing lights. If that is your model and problem please just tell me what lights are flashing.

In Maytag with display instead, the L on display means that the machine is control locked. That is not an error message, but a code telling that the machine has been locked by the user (probably by mistake since you are the user).

I quote from Maytag technical documentation:

? If a cycle or option pad is pressed after the controls have been locked, the indicator light next to lock graphic will flash five times. On selected models with a countdown display, the display will flash the symbol "L" simultaneously with lock indicator.

? This option does not lock the door, only the dishwasher controls.

To set :
1. Press the Heated Dry pad for three seconds.
2. An indicator light next to the lock graphic will illuminate when the controls are locked.

To Cancel Control Lock:
1. Press the Heated Dry pad for three seconds.
2. The indicator light will go off as instructed.

Try pressing the the Heated Dry pad for three seconds. If that doesn't work disconnect power. Connect back and try again unlock (power off does not remove the lock). If that still does not work there may be a faulty part. In that case turn appliance off and give me the full model number.

Start holding down the Heated Dry pad for three seconds. In normal conditions that is enough to get rid of the L and of control lock.

If you need parts or schematics see this tip explaining how to find parts and diagrams for most appliances: Where do I find parts and diagrams for my appliance?

Regards.

Ginko

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.



"F02" is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a "SUDS" error may also be generated as a secondary error. This is an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:

1. Check the drain hose to make sure it is not kinked or clogged.
2. Check the electrical connections to the pump and ensure the pump is running.
3. Remove the drain pump filter and check for foreign objects and/or debris.

To check the drain pump, click on the following link for step-by-step instructions.


http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

This advise is for Kenmore Elite and Whirlpool Duet front loader washers and dryers with a Control Lock problem.

This may or may not be an indication of a serious problem. In the majority of the cases, this is a simple operator error. Nearly all these model appliances have some sort of Control Lock feature on the front panel now. This is a designed safety feature that is used to prevent small children from manipulating the controls. The controls can be easily locked or unlocked by pressing and holding the following button on the front panel:

Whirlpool Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 3 seconds.

Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 3 seconds.

Kenmore Elite Dryer - Press and hold the AUTO DRY LEVEL button for 3 seconds.

These instructions may not be all inclusive for all Kenmore and Whirlpool models, but they are the most common. Chances are, if you have a Control Lock feature, the instructions will be printed on the front panel adjacent to the button that is required to lock or unlock the controls.

NOTE: These instructions may also work for newer model Maytag, Hotpoint, Admiral and Fridgidaire model front loaders as well. Refer to your owner's manual or front panel for instructions pertaining to your sepcific model.

If the Control Lock feature will not lock or unlock the appliance, unplugging the unit for AT LEAST 30 minutes is recommended in order to reset the main control board. In many cases this is all that is required to correct momentary glitches.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

I had the same problem. The lock button light was on, nothing happened when pressing start, cancel, etc. I also tried holding the heated dry button (lock) for 3 seconds and no luck UNTIL holding down for three seconds while also pressing the cancel button. I was then able to start cycle as normal.

Try the "End of Cycle" button to the right of panel front, next to Start button. Mine says hold for three seconds to lock/ unlock control.