Question about Maytag Maxima EcoConserve Series MHW6000X 27" Front-Load Washer with 5.0 cu. ft. Capacity, 11

1 Answer

Maytag maxima codes F06 and E02: Tried doing a spin/rinse/drain on an empty machine. Timer seems tpo be working but cannot hear water filling or barell spin. tried to shut off and door is now locked.

Was doing a load of wash, and came back to see error codes F06, E02 flashing onscreen and door was locked. unplugged for over night and re energized. door was unlocked os I removed wash. Tried rinse/drain and spin as suggested on line but nothing. No water fill or tub spin. door now locked again.

Posted by Jon L on

Ad

1 Answer

ernesto cuadra

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Maytag Master
  • 12,223 Answers

See this causes and fix it. God bless you
POWER/CANCEL press for to cancel the error codes.
First to unlock depending on model. There will be a pull tab either under the lower kick panel, behind the filter cover, or under the top panel. Pull this tab to unlock the door. Now you can remove the clothes and water. Refer to the owners manual for the location of your emergency door pull tab.

Door Switch
You will need to remove the door switch to check it. You will perform an ohm reading on the bottom terminals. The reading varies from manufacturers most Frigidaires is around 1500 ohms others like the whirlpool duet is checked at the main control board with the door closed should be around zero ohms. You will need to refer to the tech sheet or service manual for the proper reading.

Main Control Module / CCU
The main control unit is the circuit board located behind the console. If the door switch tests good the main control is usually the problem. Check all connections for a goood tight fit. You will need to refer to the tech sheet or service manual to check this further. The main control is easy to replace.
Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.+fuse thermal +c.breaker

Posted on Oct 17, 2012

  • Elaine D Sobell
    Elaine D Sobell Jan 25, 2019

    Just unplug the machine from the wall. Wait 20 minutes. Plug it back in. The door will open. Basically just reboot.

×

Ad

5 Related Answers

Anonymous

SOURCE: Washing machine fills, but won't agitate

maytag washer dryer stack unit , model # lse7806ace washer fills with water but won't agitate or do anything else. I had the same problem a year ago and replace the lid switch asssemby and fuse and it worked fine until now. the switch clicks when I open and close the lid and the pink and orange wires show continuity with the lid closed.

Posted on Aug 29, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: MAYTAG NEPTUNE MAH9700AWW continues to fill on rinse, code "oe",

if the water continues to fill even with power off, and you have to manually shut in off at the wall valve, the 3-way inlet valve is stuck open. you have to replace it. $90

Posted on Mar 12, 2010

Anonymous

  • 163 Answers

SOURCE: Won't run

sounds like your lidswitch.when you close lid you should hear or feel it click on and off.located on back side of lid in center.

Posted on Mar 10, 2009

Anonymous

  • 1 Answer

SOURCE: Maytag Neptune stops during rinse cycles

Could yoy please explain what the "screen" is?

Thanks,
Carl.

Posted on Sep 14, 2008

Anonymous

  • 878 Answers

SOURCE: Maytag Atlantis wont run

JC, sounds like the lid switch, check this first and post back..Catriver

Posted on Oct 30, 2006

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

Maytag maxima ecoconserve washer My washer will not operate. The lights come on as if it will I hear a few noises, but water will not enter it and it does not operate. Error Codes are E02 and F06

you have a communication error from the UI (user interface) to the CCU (Central Control UNIT). It could be the wiring or the control itself
0helpful
1answer

My may tag washer has codes F06 & E02 , what does this mean?

I beleive e02 is something to do with ur drain pump set up clogged or damaged water pump and hoses
may-tag-washer-codes-f06-e02-mean-k0kyq5w2opxaqmtqljxs4yag-3-0.jpg

may-tag-washer-codes-f06-e02-mean-k0kyq5w2opxaqmtqljxs4yag-3-2.jpg

may-tag-washer-codes-f06-e02-mean-k0kyq5w2opxaqmtqljxs4yag-3-5.jpg

may-tag-washer-codes-f06-e02-mean-k0kyq5w2opxaqmtqljxs4yag-3-9.jpg
0helpful
1answer

Washer will not run

f06 OR e02 error code means you have an interface communication error. the main control board isn't communicating with the front interface control board. if you pull the washer out and remove the 3 screws coming in from the back of the top panel. the top panel will pull straight back, up, and off. check all the wire connections between the two control board and make sure they are all secure. if everything looks good, then the interface control board may need to be replaced.
f01 e02 means that your motor control board is not reading the tachometer on your motor when it tries to turn the motor. it thinks that the motor is struggling. open the door and turn the basket to make sure it spins freely.
1helpful
1answer

What do these 2 codes mean on my maytag washer , F06 and E02?

The error code E02 and F06 on a Maytag washer could mean that the hot water solenoid went out. It could also mean that that the hot water control is not working properly.
0helpful
2answers

OL error code

Hi jbrundage1. I believe you have a UL error code on the washer. It means that the sensors in the washer are sensing the unit is unbalanced. When the washer is empty, set it to a spin or rinse and spin setting. Run the washer through the cycle empty, as it will help to remove any excess water in the tub. Also, make sure the washer is level, as it is balanced on springs, and that could be throwing the sensors off. I hope these suggestions prove helpful. Sincerely, Melanie, Maytag Social Media Representative.
0helpful
1answer

Hello I have a Maytag Washer Model A512 The machine goes through a regular cycle OK - However, it DOES drains the water out during the rinse cycle, but does NOT drain the water out during the spin...

The timer will always advance to the next program if the machine does not fully drain. There is ALWAYS a spin when draining the water out, there is only one pump and one motor. The waterlogged laundry maybe telling the timer that there is still water in the tub. Put the machine on "Spin" and cheat the lid switch into thinking that the lid is closed. Use a clothes peg or wide ended screwdriver and see if there really is a spin....
1helpful
1answer

Moffatt washer is washing and draining but not spinning out the clothes

All content © 2000 © 2009 Washerhelp
> Home / Repairs DIY washing machine advice (part 8) Washing machine sticks or stops mid-cycle repairs-sm.gif A very common fault on washing machines is when the program timer fails to complete the cycle and stops part way through. Many people blame the program timer for this but although it is a possible cause, there are many more likely causes for this fault. The program will stick if the heater isn't working, if the thermostat fails, if it can't fill up with cold water for the rinses, if it can't empty the water etc. There are too many possible causes of this fault to be able to give anything other than rudimentary advice. However, the common causes of a washing machine sticking that can easily be fixed are filling and emptying problems.
Check that the cold water supply is available to the washing machine, which is a common cause for sticking on rinses. If the washing machine appears to stop mid-cycle and isn't filling with water on rinses then see Washing machine won't fill with water (or no water goes into washing machine) before calling an engineer. If the washing machine can't drain the water out then it will stick on the rinses, or it will abort with an error code. If you can see water still inside the washing machine then check the following advice Washing machine won't empty water
Not finding what you are looking for?
Maytag Maxima EcoConserve Series MHW6000X 27" Front-Load Washer with 5.0 cu. ft. Capacity, 11 Logo

20,361 views

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Jessie Goss

Level 2 Expert

162 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6929 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...