Kenmore Washing Machines - Recent Questions, Troubleshooting & Support

0helpful
1answer

Kenmore model 253.68232800.......is there a regular on-off switch ?

No there is no on/off switch on this refrigerator. The parts diagrams are available here: https://www.searspartsdirect.com/model/2fns2ul82o-000582/kenmore-25368232800-top-mount-refrigerator-parts . There is a knob that controls how much cold air flows into the refrigerator by opening and closing the damper. I hope this helps. Cindy Wells
9/19/2021 10:40:37 PM • Kenmore Washing... • Answered 2 days ago
0helpful
1answer

Kenmore Series 400 Triple Action Agitator Washer restarts cycle after finishing

We have this exact problem. The repair guy told us it would be over $400 to replace the whole control panel. So for now we set a timer for 1 hour and if you are standing at the washer when it finishes you can open the door to prevent it from restarting. Until we get a new washer this is what we will do.
9/13/2021 6:24:17 PM • Kenmore Washing... • Answered on Sep 13, 2021
0helpful
3answers

Machine fills and agitates, but won't drain

Please empty your machine and run the machine empty. If the washer goes through the whole cycle without any clothes. Please let me know
9/11/2021 5:34:10 AM • Kenmore... • Answered on Sep 11, 2021
0helpful
1answer

Kenmore elite 22952 keeps filling til overflows, no matter what level setting

Inside the case there is a water level switch. It is round, has 2 wires to a number of connectors and a tube that goes down to the drum. As the water goes in, the water level rises in the tube and causes the pressure to operate the switch and turn the water off. If the machine was tilted or laid flat with the transit bolts not being in place, it may have caused the pipe to come off. The usually look like this. https://www.ifixit.com/Guide/Kenmore+110+Series+Washing+Machine+Water+Level+Sensor+Replacement/11037 or this https://www.searspartsdirect.com/diy/repair-guide/how-to-replace-the-water-level-pressure-switch-on-a-direct-drive-top-load-washer They are easy enough to change, but expensive. Check the pipe hasn't come off first. https://www.google.com/search?q=kenmore+elite+22952+water+level+sensor+replace ..
9/10/2021 8:39:01 PM • Kenmore Washing... • Answered on Sep 10, 2021
0helpful
2answers

What year is my kenmore washer model 110-25132411, serial # C54040367

You can determine the age of your appliance by looking at the serial number on the nameplate. The first number indicates the year of manufacture, and the second and third digits indicate the production week.
8/23/2021 3:33:55 PM • Kenmore Washing... • Answered on Aug 23, 2021
0helpful
1answer

My Kenmore washer Mod. #110.25102311 has low water level!

If the water levels are low in your washing machine then you could have a sensor that is faulty . The fill sensor will communicate with the control board when the washer is full to turn off the water . The fill sensor needs to be replaced for the water levels inside of your washing machine.
8/5/2021 1:03:46 AM • Kenmore Washing... • Answered on Aug 05, 2021
0helpful
1answer

How to change drain hose Kenmore stackable washer dryer

Is the rear of the machine accessible?
8/4/2021 2:18:25 PM • Kenmore Washing... • Answered on Aug 04, 2021
tip

Replacing a Rear Tub Bearing

Rear Tub Bearing Replacement
(Part 1 of 3)

This advice is for replacing the rear wash tub shell of most Kenmore Elite HE model FRONT LOADERS, along with Whirlpool Duet, and some Frigidaire FRONT LOADER models. This is a repair that would be rated as difficult due to the extensive disassembly and reassembly of components.

The requirement to replace the rear wash tub shell is usually attributed to the rear tub bearing failure in which the bearings are molded into the tub and cannot be replaced otherwise. In some situations the replacement of the inner spinner basket (stainless steel tub) may also be required due to the corrosion and breakage of the spider arms in the back of the basket that support the basket.

SYMPTOMS: Washer exhibits excessively loud “rumbling” type noise during the spin cycle, excessively vibrates, or won’t spin at all.

DETERMINING IF THE BEARING AND SPIN BASKET ARE BAD: With the washer door open, place your hand inside the basket and push straight up. If there is excessive play in the tub (wobbles up and down) the bearing is probably bad. If the spinner basket scrapes against the outer tub shell when you give it a spin, you will have to replace the inner spin basket as well. Unfortunately, you cannot see the condition of spinner basket supports until it is removed from the outer tub shells. In some cases, a brownish colored stain my show up on clothing as the bearing seal has been breached and leaks into the spinner basket.

Before starting this repair, make sure you read through all instructions thoroughly and place the washer is in an area that gives you plenty of space to work.

(cont’d)
0helpful
1answer

So I I bought a used Kenmore Elite Smart Wash, Quiet Pak 9, Clothes Washer and I can't get the delay switch to go off. Seems as if It's preventing the washer from running a cycle.

Disconnect the electric plug for five minutes then plug it back in spin the controlled by around two or three ways and then start over push the start button
7/19/2021 3:58:04 PM • Kenmore Washing... • Answered on Jul 19, 2021
0helpful
1answer

Kenmore 80 series washer

yes needs water to work
7/19/2021 7:42:24 AM • Kenmore Washing... • Answered on Jul 19, 2021
0helpful
1answer

Kenmore HE2+ is leaking water from below, where do I look and what do I look for?

Look underneath for water
7/9/2021 8:38:37 PM • Kenmore Washing... • Answered on Jul 09, 2021
0helpful
1answer

I have a Kenmore 85751 Washer dryer combo. Does anyone know if the dryer is gas or electric?

It shows an electric element in the spares list. If you are thinking of buying one second hand, many of the parts are obsolete. https://www.searspartsdirect.com/model/614igen521-000582/kenmore-11098575120-laundry-center-parts ..
7/5/2021 10:43:48 PM • Kenmore Washing... • Answered on Jul 05, 2021
0helpful
1answer

KENMORE WASHER HAS ERROR CODE 5D DURING RINSE CYCLE. PUT THROUGH CLEAN CYCLE AND STILL HAPPENING. CLOTHES COMING OUT TOO WET

That code is SD (suds). The code is the same for many washing machine manufacturers. This code usually means that too much detergent was used. It can also mean that a regular detergent was used in a HE machine. An extra rinse and spin cycle might help. One option is to do a wash cycle with no items in the washer or a cleaning cycle. This may remove excess detergent that has built-up over time. If the error persists when the washer is run when empty, the motor or the drain pump are working improperly. First check the drain pump filter and drain line for any foreign objects. If that area is clear, then you probably have a problem with drive hub for the washer (or another part of the wash basket spin hardware). With a Kenmore machine, the machines were made by a variety of manufacturers. Thus the locations of the drain pump filter and the wash basket spin mechanism to check for issues will depend on the machine prefix. Please add a comment with the full model number including the 3 digit prefix, if you want a parts diagram and other information to help solve this problem. I hope this gets you started. Cindy Wells
6/30/2021 5:10:42 PM • Kenmore Washing... • Answered on Jun 30, 2021
0helpful
1answer

I have a kenmore c100. 129-35713. I have lost the -plug for the drainage-know where I can buy one?

Hello, Get from the manufacturer or any store around you that deals with the Kenmore productproducts. Thanks for coming, Good luck.
6/30/2021 9:47:24 AM • Kenmore Washing... • Answered on Jun 30, 2021
0helpful
1answer

How to just run the spin cycle?

https://www.manualslib.com/manual/85754/Kenmore-29522.html#manual Kenmore 600 Series Pdf User Manuals. View online or download Kenmore 600 Series Use And Care Manual. ... Kenmore Washer Use and Care Guide. Probably the worst washing machine manual I have ever read! Try this. Put your wollens in the machine, set for cold water, Woollens Cycle and your 'Soak' detergent. It will agitate a bit, and as soon as it stops filling, turn it off. After say 20 minutes. Then Move the dial to Spin, and pull the knob out. It _should_ pump out and spin.
6/27/2021 8:21:01 PM • Kenmore Washing... • Answered on Jun 27, 2021
0helpful
1answer

Www.fixya.com/support/r385844

A perfect store where we are going to provide you all the information. With the help of this provided material, it is necessary for those who start to get essay writing. I am always going to keep that material and also maintain our store.
6/26/2021 6:34:19 AM • Kenmore Elite... • Answered on Jun 26, 2021
0helpful
1answer

Kenmore 41748102701 service manual

possible one mounted close to motor or inside cabinet
6/26/2021 5:14:35 AM • Kenmore Washing... • Answered on Jun 26, 2021
0helpful
2answers

Is it possible to bypass the door lock sensor on a kenmore 41748102701 washing machine?

Door locks are an important safety device. Did you read the story about the young boy that had his arm torn off? https://www.google.com/search?q=kenmore+41748102701+door+lock+sensor ..
6/26/2021 5:12:13 AM • Kenmore Washing... • Answered on Jun 26, 2021
Not finding what you are looking for?
Kenmore Logo

Family Lines

31,381 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Paul Carew

Level 3 Expert

3630 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...