20 Most Recent Maytag Performa LAT2500A - Page 4 Questions & Answers

0helpful
1answer

Got an error code id 11 on maytag JJW9530DDS
Possible Solutions

Reset power to the product:

There may be a problem with the Oven Temperature Sensor, the Control, or the associated wiring.
  • Power unit down by turning off the circuit breaker(s) for one (1) minute.
  • Power unit up by turning on the circuit breaker(s).
  • Monitor the oven for one (1) minute to ensure the error code does not display again.
  • Verify oven operation.
Read full answer
1/10/2023 4:08:11 PM • Maytag Washing... • Answered on Jan 10, 2023
0helpful
1answer

Maytag Neptune Model MAH5500BWW will start and one second later "door locked" light goes off and stops the wash.
The door switch and the lock for your door and the sensor that lets the door to be able to lock and start up is broken and should have to be replaced. for your washing machine
Read full answer
12/31/2022 7:57:44 AM • Maytag Washing... • Answered on Dec 31, 2022
0helpful
1answer

Maytag commercial technology washer it won't agitate just makes a clicking noise but it spins.
Something could be trapped or stuck inside the washing machines drain. Check your washing machines drain to see if something is stuck there.
Read full answer
12/20/2022 7:10:57 AM • Maytag Washing... • Answered on Dec 20, 2022
0helpful
2answers

Od code on my Maytag Front load Neptune Washer...Hi, could anyone please share more info on DIY fixes, I have tried everything under the Service mode and eventually did a Board Output Test also..
17 The door / cover switch has not been opened since the last two last revolutions. The door did not open after two complete washing cycles. The door switch has not been opened since the last two revolutions. Displays "od". If the door is open, the error disappears. Check the door lock probably bad. Also you might need to reset it. ... Press power/cancel then start/pause
  1. Press power/cancel first.
  2. Next, pick a fresh cycle to run.
  3. Press start/pause to reset your Maytag washer.
  4. Run a test load afterward to confirm that the washer has reset.
Best to you.
Read full answer
12/10/2022 9:12:37 PM • Maytag Washing... • Answered on Dec 10, 2022
0helpful
2answers

Maytag MDB6100AWW comes on and pumps water, then the motor hums for 3 seconds stops for 15 seconds then hums for 3seconds. Won't start any wash cyclesand won't pump water out
Hi, Please power cycle your machine and then rotate the cycle dial by 90 degrees counter clockwise (opposite of usual direction of rotation), then attempt to run a wash cycle again. Otherwise, I would run a rinse cycle and poor some toothpaste in the washer in order to unclog any potential blocks before attempting the wash again. Thank you.
Read full answer
12/6/2022 2:59:01 AM • Maytag Washing... • Answered on Dec 06, 2022
0helpful
2answers

How to get clothes out of a locked washing machine
Power unit down by turning off the circuit breaker or unplugging for one (1) minute. Power unit up by reconnecting power. Restart a new cycle. Monitor the washer for one (1) minute to ensure the error code does not display again. Best to you
Read full answer
12/6/2022 2:08:57 AM • Maytag Washing... • Answered on Dec 06, 2022
0helpful
1answer

Maytag Control Locked error model # MFW9700SQ1
Holding the Cycle End Signal button for 3 seconds is the way to turn the control lock off and on with this model. If that is not unlocking the control like it should, the first thing you would want to try is unplugging it for 5 minutes to let the controls reset. Best to you
Read full answer
12/5/2022 6:37:12 PM • Maytag Washing... • Answered on Dec 05, 2022
0helpful
1answer

Maytag Maxima washer error codes E01 F08
Mine was resolved after changing the Symmons slide valve at the inlet to the hoses. This valve is spring loaded and does not work if not exercised as open and close on regular basis. My hot water supply was completely shut off and cold water remained open at all time. Check the incoming water pressure by unscrewing the hoses from washer and check water outlet by filling the bucket from both sources. Symmons slide valve at the wall is W-400 and was 25 years old.
Read full answer
12/3/2022 1:00:28 AM • Maytag Washing... • Answered on Dec 03, 2022
0helpful
11answers

My Maytag commercial washer has
Unplug your washing machine for a few minutes which will let the electrical charge to dissipate from your washing machine that will let it reset then. If it is still not working unplug it for 10 minutes.Or you will have to access the real switch then which is under the lid housing by pushing the washing machines drum to the back.
Read full answer
11/29/2022 1:34:09 PM • Maytag Washing... • Answered on Nov 29, 2022
0helpful
1answer

MEDE500VPO How to tell the year
If a receipt or other paperwork is not available, the age of a Maytag washer can be found by looking at the serial number. The last two characters of the 10-digit number indicate the year and month of manufacture. A Maytag washer serial number is 10 characters long, with the last two characters being letters. Mar. 26, 2021

How can I tell how old my Maytag washer is? - AskingLot.com
Read full answer
11/28/2022 11:21:52 PM • Maytag Washing... • Answered on Nov 28, 2022
0helpful
2answers

Maytag lat9606 is overflowing from the top - leaves dirty water in water softener cup and in the bleach dispenser. pump seems to be working okay. hoses all clear. fill valve seems to be working okay
The dispensers are flushed during the wash cycle. Part of normal operation
Read full answer
11/24/2022 3:28:43 PM • Maytag Washing... • Answered on Nov 24, 2022
0helpful
1answer

Orange stains on clothing
I had detergent with oxy-cleaners do this. murf427
Read full answer
11/22/2022 4:58:12 PM • Maytag Washing... • Answered on Nov 22, 2022
0helpful
1answer

I need to cancel and drain a Maytag coin-op, front loading washer. Model number MHN33PCDWW1
Unplug from the mains. Lower the drain hose into a floor drain or a pail. You should be able to open the door. If not, run another quick wash cycle. The level switch should work now.
Read full answer
11/13/2022 6:06:06 PM • Maytag Washing... • Answered on Nov 13, 2022
0helpful
1answer

Maytag mat12csegw unbalance problem
Hi, Please reload the washer with dry clothes and attempt to wash them as normal. If the weight is distributed evenly, then the unbalanced-signal should go away once the wash starts. Thank you.
Read full answer
10/25/2022 12:59:01 AM • Maytag Washing... • Answered on Oct 25, 2022
0helpful
1answer

Maytag washer will stay on continuse cycle even after i reset the computor
bad control board
Read full answer
10/21/2022 6:04:29 AM • Maytag Washing... • Answered on Oct 21, 2022
0helpful
1answer

Maytag Neptune washer - cycle starts but then doesnt advance cycle stops
possible control timer bad or motor overheating and shutting down
Read full answer
10/21/2022 6:02:13 AM • Maytag Washing... • Answered on Oct 21, 2022
0helpful
1answer

Maytag MAH5500BWW. it cycles to the 5 minute mark, drops to 4 minutes, then jumps back up to 6 minutes and keeps cycling in this way. It does not appear to enter the final spin cycle.
bad timer control board
Read full answer
10/21/2022 5:58:25 AM • Maytag Washing... • Answered on Oct 21, 2022
0helpful
1answer

My maytag neptune washer wont spin
check belt if ok check cogs under agitator
Read full answer
10/21/2022 5:51:27 AM • Maytag Washing... • Answered on Oct 21, 2022
0helpful
1answer

Maytag Bravo MCT Top Load wont spin out at the end of the cycle, I then have to use the drain and spin cycle and it will spin out.
Hi, Please try clearing sequences by rotating the cycle dial counter-clockwise a bit before starting a new cycle. The reset should then allow your newly chosen cycle to work. Thank you.
Read full answer
10/13/2022 9:28:56 PM • Maytag Washing... • Answered on Oct 13, 2022
0helpful
1answer

Maytag centennial top load washer, Belt falls off & pulley comes loose & error code F7E1. Will bad Shift Actuator cause this?
Hi, the error relates to a motorspeed sensing error. I would advise you to get the washer serviced via maytag since there are multiple portions breaking down. You can call Maytag to get this done and learn about the actuators potential links to the machine's issues: 1 (800) 344-1274 Thank you.
Read full answer
10/4/2022 5:25:36 PM • Maytag Washing... • Answered on Oct 04, 2022
Not finding what you are looking for?
Washing Machines Logo

39 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Maytag Neptune MAH5500B Front Load Washer
Maytag Neptune MAH5500B Front Load Washer

2,981 Questions

Maytag Neptune FAV6800AW Top Load Washer
Maytag Neptune FAV6800AW Top Load Washer

1,498 Questions

Maytag Atlantis MAV6000 Top Load Washer
Maytag Atlantis MAV6000 Top Load Washer

947 Questions

Maytag PAV2300 Top Load Washer
Maytag PAV2300 Top Load Washer

680 Questions

Maytag EPIC MFW9700S Front Load Washer
Maytag EPIC MFW9700S Front Load Washer

658 Questions

Top Maytag Washing Machines Experts

Robert

Level 3 Expert

1036 Answers

Brad Brown

Level 3 Expert

19166 Answers

Steve

Level 3 Expert

3290 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maytag Washing Machines

  • Maytag Washing Machines

Most Popular Question

washer stopped

  • Washing Machines
Loading...