Xerox Phaser 6100/DN Laser Printer - Answered Questions & Fixed issues
An unsupported black toner cartridge is installed
Some replacement cartridges require a new "chip" be installed to tell the printer that the cartridge is a match. I would check with New Egg and see if they forgot to send the chips, if required. I don't know of a manual bypass to the system.Dave W.
9/14/2012 1:39:40 PM •
Xerox Phaser...
•
Answered
on Sep 14, 2012
•
2,127 views
Colour Printing
YES, Possible faulty / contaminated Transfer system, I would get this serviced, as this is a more complex fix
8/22/2007 3:00:48 PM •
Xerox Phaser...
•
Answered
on Aug 22, 2007
•
106 views
Xerox phaser 6500 will not recognize the magenta
Magenta toner(s) not being recognized, I looked into the little slot on printer where chip slides in and found one of the four contacts was bent up out of position. Rather than risk further damage by poking it in such a confined space I am going to remove the part first.
11/25/2016 12:57:53 PM •
Xerox Phaser...
•
Answered
on Nov 25, 2016
•
729 views
Error code e1 showing at xerox pro 420? solution..
rror codes
If the printer's front panel displays a message
Error XX, find the error code in this table and follow the instructions for resolving the problem. If problems persist, check the Xerox web site
www2.tek.com/TekSMART/ or contact service.
Error
User Corrective Action
Error 01
- Remove and re-install the black Toner Cartridge, then turn the printer off and on.
- Replace the black Toner Cartridge, then turn the printer off and on.
Error 02
- Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.
- Replace the cyan Toner Cartridge, then turn the printer off and on.
Error 03
- Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.
- Replace the magenta Toner Cartridge, then turn the printer off and on.
Error 04
- Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.
- Replace the yellow Toner Cartridge, then turn the printer off and on.
Error 05, 10, 11,12, and
13
- Turn the printer power off, then on.
Error 20
- Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
- Remove and re-install the Main Charge Grid. Turn the printer off, then on.
- Remove and re-install the Transfer Kit. Turn the printer off, then on.
- Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.
- Replace the Main Charge Grid. Turn the printer off, then on.
- Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
- Replace the Transfer Kit. Turn the printer off, then on.
- Replace the Toner Cartridges. Turn the printer off, then on.
Error 21, 22, 30,and
32
- Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
- Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
- If a problem persists for Error 30, clean the sensor. See Cleaning Phaser 750 Printers.
Error 33
- Check for jammed paper throughout the paper path (especially in paper feeder).
- Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.
Error 40, 41, 42,and
43
- Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.
- Make sure that you have the correct Fuser for your local printer power supply:
110-Volt Fuser Part Number 016-1839-00
220-Volt Fuser Part Number 016-1840-00
- Replace the Fuser. Turn the printer off, then on.
Error 50, 51
- Turn the printer off, then on.
Error 52
- Remove the Duplex Unit (if installed).
- Check for paper under the Upper Tray.
- Turn power off, then on.
Error 53
- Open left door and remove any jammed media.
- Tun the printer off, then on.
Error 60
- Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.
- Reinstall the media. Make sure you do not overfill the tray.
Error 61
- Remove and re-install each Toner Cartridge. Turn the printer off, then on.
- Replace each Toner Cartridge. Turn the printer off, then on.
Error 62
- Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).
- Remove and re-install the Fuser. Turn the printer off, then on.
- Slide out and re-insert the paper feeder. Turn the printer off, then on.
- Replace the Fuser. Turn the printer off, then on.
Error 63
- Remove and re-install the Imaging Unit. Turn the printer off, then on.
- Replace the Imaging Unit. Turn the printer off, then on.
Error 70, 71, and
72
- Turn the printer off, then on.
Error 73
- Remove and re-install the Imaging Unit. Turn the printer off, then on.
- Replace the Imaging Unit. Turn the printer off, then on.
Error 74
- Remove and re-install the Fuser. Turn the printer off, then on.
- Replace the Fuser. Turn the printer off, then on.
Error 80, 81, 82,83, and
84
- Make sure that all four toner cartridges are installed in the printer.
- Turn the printer off, then on.
Error 01p through
Error 47p
- Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).
- you can helpful
9/9/2016 1:25:18 PM •
Xerox Phaser...
•
Answered
on Sep 09, 2016
•
329 views
Not finding what you are looking for?