20 Most Recent Xerox Phaser 7300DN Laser Printer Questions & Answers

0answers
0helpful
1answer

Jams when duplexing

There is a set of clutches in on the upper back side of the right side door.
The inverter clutch tends to go bad on that cluster.
But if you are replacing one may as well do both. They are electromechinical clutches.
11/19/2015 10:32:14 PM • Xerox Phaser... • Answered on Nov 19, 2015
0helpful
1answer

I have a phaser 7300 that asks for a transfer unit...

I think you might have a Spring missing for the Waste Toner Full Sensor. The machine tolerates the sensor status for 2K pages and then shuts it down.

Truthfully, it is really hard to describe in a few sentences. It belongs in the frame wall under near where you have the white waste toner section of the Transfer Belt. This spring pushes a flag up that hits the Paper Entrance Sensor (yes, near the bypass tray)

The PN for the spring is 116-2050-00.

Whit
Item, Inc.
8/5/2015 4:00:35 AM • Xerox Phaser... • Answered on Aug 05, 2015
0answers

Transfer belt

Be the first to answer 1/15/2014 3:19:47 AM • Xerox Phaser... • Posted on Jan 15, 2014Be the first to answer
0helpful
1answer

Reset imaging unit life

Usually it should do it automatically once you have replaced to a New image unit. If you are still getting that error then you will have to change the engine control board. You can first try this tip reset the nvram from the service diag mode some errors get stuck in the NVRAM and won't get off until a reset is done in the NVRAM. Hope this helps. Iteminconline
11/26/2013 1:33:20 AM • Xerox Phaser... • Answered on Nov 26, 2013
0helpful
1answer

Paper jams by rolling to the fuser casing.

you must configure the page size, because the configuration jams have a page shorter than the product that you put to print.
10/25/2013 11:02:23 PM • Xerox Phaser... • Answered on Oct 25, 2013
0helpful
3answers

Horz. streak approx.3/4 down on each page I print

Sounds like some of the magenta toner is left behind on the drum. The only way to fix it is to get a new cartridge.
6/5/2013 9:54:05 PM • Xerox Phaser... • Answered on Jun 05, 2013
0helpful
1answer

Xerox 7300 print is pixilated

This depends on what you are trying to print and with what software. Most likely, you need to choose a higher print resolution in the software before sending to the printer, but more details would be required to give a precise response.
5/5/2013 3:11:30 AM • Xerox Phaser... • Answered on May 05, 2013
0helpful
1answer

Changing resolution

You set the resolution in the printer driver before sending the data to the printer. Exactly where this will be will depend on which OS you are using and which software / driver you have installed.
5/5/2013 3:06:10 AM • Xerox Phaser... • Answered on May 05, 2013
0helpful
1answer

Colour misregistration mystery

Various possible causes - the most likely are :1. Dirty registration sensors - remove IUs and transfer unit and inspect / clean sensors.2. Damages / worn IU drive gears - inspect. Replacing the gears isn't a small job, if this is your problem.3. Faulty colour registration shutter - you can check this is working in the service diagnostics menu.4. EEPROM problem on the controller board - replace main controller board.These are in order of likeliness. For further information, take a look here.
5/5/2013 3:02:07 AM • Xerox Phaser... • Answered on May 05, 2013
0helpful
1answer

Error u26 phaser 7300

U26 is Yellow Image Unit failure. It may be that the contacts are dirty - spilled toner?? Give it all a thorough clean, especially where the electrical contacts are - if still no luck, then a new yellow IU should solve the issue.
5/5/2013 2:47:10 AM • Xerox Phaser... • Answered on May 05, 2013
0helpful
1answer

Help with u2 code on phaser 7300

U2 is an engine EEPROM failure - you'll need to replace the main board to fix that, I'm afraid.
5/5/2013 2:44:30 AM • Xerox Phaser... • Answered on May 05, 2013
0helpful
8answers

Phaser 7300 error message...

The problem is a crazy design in the printer itself! I've now found a reliable fix for this problem which is relatively easy to carry out. You will find the details of how to do it here :www.michelsplace
5/5/2013 1:24:54 AM • Xerox Phaser... • Answered on May 05, 2013
0helpful
1answer

Advice phaser 7300dn appear 10: eeprom ,help me please!

Hi,

The only thing you can do is attempt a reboot and hope for the best, otherwise call out an engineer to repair it! Or you could try and NVRAM reset but I'm not sure if that will work and be careful because you will set the machine to factory settings and may have to do a colour calibration all over again. Let me know how it goes.

Resetting all settings to default (NVRAM)
Resetting the NVRAM will reset all printer values including network, printer setup, job defaults, and color calibrations.
  1. Press the Down arrow key and scroll to Support.
  2. Press the OK key.
  3. Press the Down arrow key and scroll to Service Tools Menu.
  4. Press the OK key.
  5. Reset NVRAM will be displayed.
  6. Press the OK key.
  7. Reset NVRAM and Reset Printer NOW will be displayed.
  8. Press the OK key to reset all the settings to default.
1/8/2013 3:24:58 AM • Xerox Phaser... • Answered on Jan 08, 2013
Not finding what you are looking for?
Xerox Phaser 7300DN Laser Printer Logo

175 questions posted

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Ekse

Level 3 Expert

13435 Answers

Cindy Wells

Level 3 Expert

6412 Answers

Mehandi Husain ...

Level 3 Expert

1654 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Phaser Xerox

  • Phaser Xerox

Most Popular Question

phaser 7300 error message

  • Office Equipment & Supplies
Loading...