Sunbeam 805810 HeatSense Heating Pad Heater - Answered Questions & Fixed issues

Crimped the ends of the heating pad cord where it attaches to the pad a little then did the plug and unplug three times while holding down the on-off button and that did the trick

have same problem with heating pad . reset control by unplugging unit for 1 minute , while holding down power button plugged unit back in . sometimes this takes 3 or 4 tries.

I had this problem with a heating pad too. I tried turning it off, unplugging it, then plug it back in and see if the light is still blinking. If it's not, set it to the temp you want. My heating pad was very temperamental that way, it didn't want to be set before it was plugged in. I hope this works for you.

You should be able to get the manual from Sunbeam or here

You should be able to get the manual back from here.

Hi, you should be able to get the manual here:http://manualfox.com/link/sunbeam.htm

Check the manual.
If you dont have one, ask here to get it.

I just took mine apart and there is nothing inside that can be fixed (like a fuse.) Sometimes I could get it to work by unplugging it for a minute then plug back in and it would work for a while, but now nothing... It is junk. Walmart has pads for around $15. Also, I found some vibrating heat pads online for around $24.

Good luck!

Same F2, quick off problem here. Then I noticed that the gray plug on the power cord was not completely flush with the connector on the pad. I shoved them together until there is no gap. The unit's worked perfectly since then.

I have contacted the company and they are going to replace my heating pad once it is back in stock.

Thank you

Sure, here are a few suggestions on where to find a replacement controller for your Sunbeam BL0750 electric blanket:

* **Sunbeam customer service:** You can contact Sunbeam customer service directly and they may be able to help you find a replacement controller. Their contact information is available on their website.
[Image of Sunbeam customer service website]
* **Online retailers:** There are a number of online retailers that sell replacement controllers for Sunbeam electric blankets. A quick search should turn up a few options.
* **Local hardware stores:** Some local hardware stores may also carry replacement controllers for Sunbeam electric blankets. It's worth checking with your local store to see if they have any in stock.

Once you've found a replacement controller, you can either install it yourself or have a professional do it for you. If you're not comfortable installing the controller yourself, you can take your blanket to a qualified electrician or repair shop.

Here are some additional tips for troubleshooting your Sunbeam BL0750 electric blanket:

* Check the power cord to make sure it's plugged in securely.
* Try using a different outlet.
* Check the fuse or circuit breaker to make sure it's not tripped.
* If you've tried all of these things and the blanket still doesn't work, you may need to replace the controller.

I hope this helps!

There is chance that arcing brushes in the motor are causing the odor. They should be replaced and the armature cleaned. A sunbeam repair shop can refurbish your mixer if the parts are still available.

Nothing works. Have had it for 6 months. Plugged in after so long, still blinking.

compressor not working or low on freon

A partstore knows or chec online

heating element possible shorted out.

Try these: -Make sure the remote battery contacts are clean; -clean fully charged battery surfaces with a lead pencil eraser to remove oxide; -could be loose contacts or cold solder joint on remote control board, especially if dropped a lot. if not tech savvy probably better to recycle old unit and purchase a new one . good luck!

Generally means u have a bad connection at the wall or at the control module. Disconnect everywhere u can and reconnect

Possible free manual if this is the same model with wick information. http://www.milesstair.com/Sunbeam3602.pdf

Try unplugging the power cord from the wall socket and check that the connection to the blanket is good and not loose. Then plug back into the wall socket and switch on. If error still occurs then there may be a problem with the blanket.