Heating & Cooling - Recent Questions, Troubleshooting & Support

0helpful
3answers

How to change bulb in amish heat surge heater

It's not difficult to change the bulb. But lengthy to explain. If you no longer have your Owners Manual go the link below and click on "Flame does not illuminate properly" More than likely though, the bulb(s) have just come loose.

http://www.heatsurge.com/help/troubleshooting.cfm
1/31/2023 4:17:59 PM • Heating &... • Answered 27 minutes ago
0helpful
1answer

Why does my glo warm lp heaters pilot seem to have to much pressure to light

no info generic answer regulator out of adjustment -failing ---orifice failing ---valve failing
1/31/2023 4:13:43 PM • Heating &... • Answered 31 minutes ago
0helpful
1answer
0helpful
1answer

All pro SPC 150T propane heater. starts and runs great for 10 minutes and then shuts heat down and blows only cold air. let sit for time and it repeats process.

It is possible that the problem with your All Pro SPC 150T propane heater could be caused by a faulty gas regulator or pressure switch. The gas regulator controls the flow of propane while the pressure switch controls the temperature of the heater. You may need to replace the gas regulator or pressure switch in order to get your heater running again. Additionally, you could also check for any loose connections or clogs in the fuel line.
1/30/2023 3:08:59 AM • Heating &... • Answered Yesterday
0helpful
1answer

My valour fireplace electrical box is making a buzzing noise. As the remote won't start the fireplace, it's probably a short circuit. Anyone else have this problem?

It is possible that your Valour fireplace electrical box is making a buzzing noise due to a short circuit. You should contact a qualified technician to inspect the unit and determine the cause of the issue. It is also possible that the remote is not working due to a faulty connection or a dead battery.
1/29/2023 6:52:58 AM • Heating &... • Answered 2 days ago
0helpful
1answer

630 Eurosit 0630545 ventless fireplace

It is possible that your 630 Eurosit 0630545 needs a deep cleaning or a replacement part. The loud poof sound could be caused by a buildup of dirt and debris in the burner or a faulty part. You should contact a qualified technician to inspect the unit and determine the cause of the issue.
1/29/2023 6:51:31 AM • Heating &... • Answered 2 days ago
0helpful
1answer

WHERE ARE THE LIMIT SWITCHES LOCATATED ON THE WEILDER XP60

The limit switches on the Weiler XP60 are located on the front panel of the machine. The switches are used to control the speed and power of the welder. They can be adjusted to set the maximum and minimum power levels for the machine.
1/29/2023 6:50:24 AM • Heating &... • Answered 2 days ago
0helpful
1answer

What's the code E1 stand for

Typically, the E1 Error Code means that your boiler is running low on pressure, which is the cause of the boiler locking out and not working. When you see this code being displayed, all you have to do to fix it and get things back to normal is to repressurise your boiler.Aug 11, 2022

What does E1 mean on a boiler? E1 error code solutions

https://heatable.co.uk > boiler-advice > e1-boiler-fault-code
About featured snip ..
1/29/2023 6:41:09 AM • Heating &... • Answered 2 days ago
0helpful
3answers

Red LED on honeywell r6660d

The problem is that the 2 units are "not speaking to each other". this could be caused by low batteries or a loss in signal caused by a powercut or an objection in the way of the 2 units.

first you need to turn the power off to the r666od (or otherwise known as the HC60NG) for 10 secs, then turn back on. then hold the grey button in for 15 secs. release then hold in for a further 5 secs.

go to the honeywell cm61 press the off button. hold temp up. temp down and prog 1 in for 3 secs until the dipslay goes to INST. at this point release all 3 buttons then press the i button until a beacon starts flashing.

this is now the end to your problem.

N.B the reason the green light was on is because the man override button will have been pressed.

hope this helps
1/28/2023 11:44:53 PM • Honeywell... • Answered 2 days ago
0helpful
1answer

Can the parts be purchased separately for a PLM-13000E portable air conditioner?

yes notify manufacturer or online search
1/28/2023 6:09:05 PM • Heating &... • Answered 2 days ago
0helpful
2answers

How do I reset all

How do I override settings on a Honeywell thermostat RTH221B
1/28/2023 5:51:47 PM • Honeywell... • Answered 2 days ago
0helpful
3answers

Anyone have a wireing diagram for a nordyne E1EH-015HA

Intertherm does not offer a wiring diagram for the E1 series anymore. So I have included a link to the E2 series. They are very similar and you may find this service manual helpful for whatever problem you may be having.

http://www.nordyne.com/literature/359a.pdf
1/28/2023 4:18:53 PM • Heating &... • Answered 3 days ago
0helpful
4answers

Big buddy Heater - 20 lb tanks won't keep pilot lit,

I had the same problem I called tech support and they said to turn the valve on the 20# cylinder on very slowly for the first 1/4 turn then all will be fine. There is an excessive flow check valve that causes restricted flow when the valve is opened quickly----------mine works fine now
1/27/2023 11:58:28 PM • Mr. Heater Mr... • Answered 3 days ago
0helpful
1answer
0helpful
2answers
Not finding what you are looking for?
Heating & Cooling Logo

135,436 questions posted

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

3745 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

john h

Level 3 Expert

28477 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...