Don't sweat the small stuff.
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"In memory block 4-1 for the extension's port, The Lkey for the CO line is lit green for..."
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"Speaker - "60" - Speaker. This is the default setting for Voice / Tone toggle."
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"While the station is ringing - Press "1" The feature must be enable in programming to be..."
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"You must find someone who can get into the System Manager box, or has System Manager..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"For System Speed dial, you can only do it from a port with Attendant Features. Typically..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"For the DTU phone on an NEC Elite system: Memory Block 4-12 put in the port number and the..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"did you get the email?"
Anonymous posted an answer for this NEC DTU 8D-2 Corded Phone:
"Ok. You will have to find someone who has access to system manager, or has system manager..."
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"Someone with System Manager access would have to do it. They can either default it, or..."
Anonymous posted an answer for this NEC DTU 8D-2 Corded Phone:
"A button must be programmed as a "headset" key. When activated, it will lamp red, and put..."
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"If this is an NEC Elite system, you must be on a phone with "attendant" features. By..."
Anonymous posted an answer for this NEC DTU 8D-2 Corded Phone:
"Feature 69 Feature"
Anonymous posted an answer for this NEC Electra Elite 32D-1 Corded Phone:
"It sounds as if that particular extension is in Do Not Disturb. From that phone, try..."
Anonymous posted an answer for this Lands Phones:
"There are two standards, 568A and 568B. As long as both ends of the cable are wired alike,..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"If you have an in-skin EliteMail VM, when you get into your mailbox go to the Setup..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"On your phone check to see if the MIC light is on. Feature +"1" controls the MIC."
Anonymous posted an answer for this NEC Electra Elite 32D-1 Corded Phone:
"FEATURE + 26"
Anonymous posted an answer for this NEC Electra Elite 32D-1 Corded Phone:
"How was the T1 tested? If they did it remotely and ran a typical 5-15 minute test, it may..."
Anonymous posted an answer for this NEC Electra Elite 32D-1 Corded Phone:
"The Night mode of the phone system is merely a second ring pattern on the phone system...."
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"Press FEATURE - 0 use the arrow keys to adjust press FEATURE"
Anonymous posted an answer for this NEC Dterm DTP 16D-1 Corded Phone:
"You can toggle each individual phone extension as to whether or not it recieves a "voice"..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"Jennifer, if it is a CallBack Request, it will be cleared when you speak with the..."
Anonymous posted an answer for this NEC Electra Elite DTU 16D-2 Corded Phone:
"Press Feature. Dial _9#. Enter hour and minute via dialpad. Press Recall to change AM/PM..."
Anonymous posted an answer for this NEC DTU 16-1 Corded Phone:
"It requires a headset key to be programmed in Memory Block 4-12 as a type of Feature..."
Anonymous posted an answer for this NEC DTU 16-1 Corded Phone:
"Sounds like the mic is turned off. Try "FEATURE - 1". You may have to do it twice."
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"If the VM is an in-skin for the NEC, you can't accomplish this thru System Admin via the..."
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"I am making the assumption that only line 1 has caller-ID. Both of my suggestions require..."
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"With a call in progress, press CONFERENCE, dial the internal or external number (you may..."
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"With a call in progress, press CONFERENCE, dial the internal or external number (you may..."
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"You will have to get into the programming mode and change Memory Block 4-01 for the port..."
Anonymous posted an answer for this NEC Electra Professional ETW-16DC-2:
"If the person you are trying to reach is speaking to another internal extension, none of..."