Paul wrote a tip for Audio Players & Recorders:
"For model AZUR 740A with random DC-error on display after power on. Only several..."
Paul posted an answer for this Office Equipment & Supplies:
"did you reset the lamp hours counter ?? see the leaflet that came with the new lamp..."
Paul posted an answer for this Eiki LC-X50M Projector:
"Normally replacing the individual panels is not possible, they are factory alligned. But..."
Paul posted an answer for this Eiki LC-XB15 Multimedia Projector:
"probably dirty switch contacts, or interupted wiring"
Paul posted an answer for this Eiki LC-SB20 Projector Multimedia Projector:
"this can only be solved with remote control or connect the AC cord while pressing the..."
Paul posted an answer for this Eiki LC XNB3 Multimedia Projector:
"there might be a bad connection between the input board and the main board. There are..."
Paul posted an answer for this Eiki LC-XB20 Projector Multimedia Projector:
"The signal type settings wrong in the menu, or broken interconnection between input board..."
Paul posted an answer for this Eiki LC-XG110 Multimedia Projector:
"long cables should be of perfect quality with low electric capicitance. otherise echoes..."
Paul posted an answer for this Eiki LC-X1100 Multimedia Projector:
"check the input settings , it should be at input 1 / analog RGB"
Paul posted an answer for this Eiki LC-XB28 XGA LCD Projector Multimedia Projector:
"one of the primary power circuit parts might be broken converter IC somtimes fails due to..."
Paul posted an answer for this Eiki LC-XB15 Multimedia Projector:
"try to use a full wired VGA cable, so the laptop can recognize the external display/ ..."
Paul posted an answer for this Eiki LC-XG210 Projector Multimedia Projector:
"a broken fan, or short circuits om mainboard/ sub power boards."
Paul posted an answer for this Eiki LC-XE10 Projector Multimedia Projector:
"a short circuit in one of the power lines on the mainboard is most of the time the reason..."
Paul posted an answer for this Eiki LC-XT3 Multimedia Projector:
"the mains fuse of XT3 is 15 Amps. P/N 423 028 4209, is special large type"
Paul posted an answer for this Eiki LC-XG210 Projector Multimedia Projector:
"these are the signs of a broken bulb or a failing lamp ballast unit. this is a aged model,..."
Paul posted an answer for this Eiki LC X4L LCD Projector:
"one of the many fans in this model stopped"
Paul posted an answer for this Eiki LC-X1100 Multimedia Projector:
"temperature issue, clean the air-filters at the carrying handle side"
Paul posted an answer for this Eiki LC-SM4 Multimedia Projector:
"computer should always be connected with 15 pin VGA to DVI-I cable. Select in menu input 1..."
Paul posted an answer for this Eiki LC-XB28 XGA LCD Projector Multimedia Projector:
"broken lcd panel, entire optical prism assy to be replaced, costly !!"
Paul posted an answer for this Eiki LC-XB15 Multimedia Projector:
"broken lamp or ballast unit both are costly"
Paul posted an answer for this Eiki EIP-3500 DLP Projector:
"in menu, select OPTIONs2 OItem and select PRJ mode, set this to Ceiling+ front or Table..."
Paul posted an answer for this Eiki EIP-2500 Multimedia Projector:
"broken lamp or bad rotation of the colourwheel, a common problem for this model."
Paul posted an answer for this Eiki LC-X50M Projector:
"in menu choosesetting option CEILING and set to ON."
Paul posted an answer for this Eiki EIP-2500 Multimedia Projector:
"The bearing of the colourwheel is locked. No rotation of colourwheel possible, then also..."
Paul posted an answer for this Eiki LC X986 Multimedia Projector:
"No led ? Check primary powersupply circuits for dried out ( smd) capacitors."
Paul posted an answer for this Eiki LC-X50M Projector:
"is this after auto shut down ? check menu setting if this is set to READY, then it will..."
Paul posted an answer for this Eiki LC X986 Multimedia Projector:
"At the side of the carrying handle you can pull out two grey plastic frames, these are the..."
Paul posted an answer for this Eiki LC-XB15 Multimedia Projector:
"in setting menu choose the icon with the upside down R ,press select and with arrow keys..."
Paul posted an answer for this Eiki LC-XB28 XGA LCD Projector Multimedia Projector:
"broken pins/ wiring of the signal cable. Is there blue screen when there is no input ? Try..."
Paul posted an answer for this Eiki LC-XG110 Multimedia Projector:
"you have to press the red button twice !! on screen you should see POWER OFF ? after..."