Black screen pushing red to green donot work do not hear any beep

is it a ps3? and is it just showing a black screen? if so you should try this, when it is off (red light is glowing on power button) push and hold down the power button when you first push it you hear a beep while you hold it down you will hear another beep when you do release the button and see if it comes on, I had the same problem and that solved it

Replace the medieval TV.

To turn off the service light that is flashing red on your V4 BHM ceiling lift, you have to proceed this way:
1- Power off the lift with the red cord
2- On the hand controller, push on the PROG + RETURN button at the same time and maintaint it
3- Power on the lift
4- Keep pushing on both buttons, and push in order: UP, DOWN, LEFT, RIGHT.
5-The green light will flash and the buzzer will beep 5 times
6- Release all buttons on the hand controller.
7-Push on the UP button many times, till your hear 4 beeps
8-Push the PROG button once.
9-Push on the LEFT button many times, till your hear 3 beeps
10- Push the PROG button once.
11-Power off the lift with the red cord, then back on.
The service light should be off.

You have a possible hardware problem! Is the monitor light green or amber/red? If it's the latter it's not getting a video signal which means it can be anything from the cable to the video card to the motherboard etc! Do you hear any beeps from your computer or just 1 on start up? 1 beep is normal any more and it will spell out a fault code! More details are required for an accurate diagnosis!

"from the ceiling fan we have black, blue, and white. On the mounting bracket is green. We installed black and blue from the fan motor to the black in the ceiling."

If your fan is working and the light isn't and they are tied to the same wire (black wire), then you might have a bad pull chain switch or bulb.

You may have messed up the Screen-Settings, to solve this try this.

Step 1: Turn off the PLAYSTATION 3 by holding the Power button on the front of the unit till the Power light is red.

Step 2:

1. Touch and hold the Power button, you will hear the first beep, meaning the PLAYSTATION 3 is powering on.
2. Continue to hold the Power button and after about 5 seconds, you will hear a second beep, indicating the video reset.
3. Continue to hold the Power button and after about another 5 seconds you will hear a third beep and the system will power off (Power light is red).

Step 3:

1. Touch and hold the Power button, you will hear the first beep, again for the PLAYSTATION 3 to power on.
2. Continue to hold the Power button and after about 5 seconds, you will hear a second beep for video reset.
   
3. Continue to hold the Power button and after about another 5 seconds you will hear a quick double beep. At that point release the Power button. If you succeeded in activating Safe Mode, you will see a message on the screen saying, "Connect the controller using a USB cable and then press the PS button."
4. Connect a USB cable to the controller and the PLAYSTATION 3 and press the PS button to enter Safe Mode.
5. Then you will see the Safe Mode menu.

Step 4: We recommending performing the safe mode options in the following order until one of the options works for you. If one of the options work, do not continue onto the other options.

1. Restore Default Settings
2. Restore File System
3. Rebuild Database
4. Restore PS3 System (This will wipe your harddrive, so remember to backup savegames.)

On a Nuvi 200W, when you plug in the charger, the battery status icon should go away indicating that you are no longer on battery power and that you are now running on an external power source. You should also hear a beep when you plug in the charger.

To go into charge mode, move the on/off switch to the left like you would be going to turn it off but only hold it on long enough until you hear it beep or the screen goes black and says "Battery Charging". When the battery is fully charged, touching the screen, it should say "Battery Charge Complete". If its not fully charged, touching the screen, it will say that it's still in charge mode.

- Jim
SHARCNET-USA

First plug the charge adapter into an outlet, then plug into the unit. Push the power button to turn the unit on. Now, push the button for the light. The light should come on. At this point you hit the charge button and the green light should start blinking and there will no beeping. Then turn off the light. The green light should continue to blink and the unit will charge. This worked for me, hope it helps!

i have the problem when i turn power on 2 green wash cycle lights plus the red lid lock stay on with constant beeping every second then when i push the start button the 2 green lights go out and the red lid lock light stays on but no beeps please help

Hi, depends on the beep sequence, it could either ba a bad memory or a bad video card. By being bad does not necessarily mean defective but could possibly be just loose. Try to open the casing/cover and reseat/push back into place the video card (if it is not built-in) and/or the memory. It is possible that they were jarred loose while in transit. Pls make sure the unit is unplugged before doing this. BTW, being new, you might void your warranty if you open the casing, pls check your warranty card. Hope this works out for you. Please let me know how things turn up. Regards