Question about HP Photosmart D7160 InkJet Printer

Open Question

Why does my D7160 print pictures too dark when printing from the card reader

Or computer but normal when the SD card is inserted in the printer, itself?

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 234 Answers

SOURCE: Printer keeps saying insert memory card

The message is not an error message and does not indicate an issue with the product. The message is designed to be an invitation to print photos from a memory card. Follow these steps to insert a memory card into the product. For more information please check the link bellow: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01436439&cc=us&lc=en&dlc=en&product=3194498 Good Luck

Posted on Sep 28, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: Help!!!

*** Fix your HP Photosmart D7360 (Reset Code/Master Reset) ***

1- Turn off power and unplug from power source.
2- Open right side of printer (looking at the front).
3- Disconnect,by pulling gently, both white flat ribbon cables off the main circuit board.
4- Plug in power source and turn printer on. Wait till you get a error message and push "Ok".
5- Unplug power source.
6- Reconnect the flat ribbon cables by aligning and carefully pushing into the conectors on the main circuit board.
7- Plug in power source and turn printer on (Printer preparing occurred).
8- voila, the nasty error message 0xc18a0001 "Ink System has Failed" is now gone.

/Putte

Posted on Oct 05, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: Can't Print on Card

I had the same problem with my 3 year old HP Officejet 5610. Feeding heavy paper or white card stock would result in a paper jam. The card stock would start to feed, but then stop half way. The pinch rollers seemed to spin without advancing the paper, even if the paper was fed one sheet at a time.

Solution: Clean the rubber pinch rollers with isopropyl rubbing alcohol. Partial disassembly/reassembly required.

To access the rollers, remove the scanner plate:
1. Disconnect power, USB, and phone cables.
2. Open up the scanner sheet feeder by tilting it left.
3. Unlatch the scanner scanner feeder so that it opens completely vertical. Latch is on front hinge only.
4. Remove the 4 corner hex screws on the scanner plate. Remove the 2 hex screws on the sheet feeder. (I used a small flat blade screw driver in the hex heads)
4. Lift the plate and sheet feeder away from printer box. Disconnect the 2 flat cable wires from the circuit board.
5. Scrub rubber pinch rollers with alcohol on a swab. Dry thoughly.
6. Reassemble. (NOTE: This is a good time to clean the underside of the glass plate and the scanner head)

Posted on Oct 15, 2008

Anonymous

  • 93 Answers

SOURCE: Ink not printing the same image quality that is on computer

Issue When printing directly from a memory card, the printouts have an abnormally high red tone.
NOTE: This does not affect the prints that were originally sent from the computer. Solution Press the Photo Fix button to turn off the Photo Fix feature before printing from a memory card. Cause The Photo Fix feature was originally designed to reduce/enhance printed pictures by making colors more vibrant. However, it can also have a side-effect to make some prints have more red tone than desired. In the HP Photosmart D7100 series printer, this feature is “ON” by default.

Posted on Dec 15, 2008

rulds2008

Grand Canyon Tech

  • 3866 Answers

SOURCE: Printer won't print in black ink.

Plunger needs to be cleaned, print head also would need to be looked at on this one.


Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I WOULD LIKE TO HAVE A MANUAL FOR INSTRUCTIONS ON HOW TO INSERT MY MICRO SD CARD INTO MY COMPUTER AND WHAT TO DO WHEN I INSERT THE MICRO SD CARD


You'll need an adapter to convert the Micro SD card into a normal size SD card, slot the Micro SD into the SD card adapter and then plug that into the computer.
Most computers then pop up a box to tell you that you've plugged something in, so you can then browse what is on the card.
Double clicking on the items on the card will then enable you to view the images/items.

Aug 16, 2016 | Cell Phones

1 Answer

I am trying to upload photos from my camera's sd card. Normally I just attach the camera to a usb cord and do it that way, but at the current moment all I have is the SD card and am in diar need of...


Hello. You can transfer it without the USB cord and camera IF you have an SD card reader. Some computers have already built in card reader, so if your computer have one, just insert the SD card and start uploading. But if your computer doesn't have it, then you need to get a card reader, insert the SD card into it, and then insert the card reader into a USB slot in you computer. Card readers are really cheap.

Thanks for using Fixya!

Jun 07, 2011 | Posiflex SD 100 (SD1008012) Magnetic Card...

1 Answer

New sd card, when putting it into my hp 8250 the printer says "card access error". I need the photos that are on the card!


Try downloading the photos off the SD card by inserting the SD card into anUSB card reader and connecting it to a computer's USB port.
This computer should detect the SD card as an external storage device, then you can copy the photo from the SD card to your computer's hard disk.

May 26, 2011 | HP Photosmart 8250 InkJet Printer

1 Answer

I imported all my photos onto my computer. Now, after re-inserting the sd card, the camera says "card locked" when I try to take more. Help


Hello

OK, if the memory card itself is locked, you might sometimes get this error code. All you need to do is to take out the memory card and switch the lever on the left side to the unlock.

6c99e31.jpg

If the error is still displayed after you did the above, you might want to try the card in another camera.

If the card works in another camera . the problem is with your card reader in your camera.

If you open you sd slot and look inside with a sharp light , you should be able to see on the left side of the slot there is a little copper or spring steel lever switch. This switch work as follows:

1. When no card is inserted / no write protection , the switch is open and thus the protection is off.
2. When locked card is inserted , the tab is depressed and tells the camera that the card is lock.

Contrary to popular belief ,the little tab on the sd card is not an electronic switch and does not physically influence the card operation itself. If you put a locked card into a camera without a sd lock switch , you would still be able to use the card normally.

It is incredible difficult to fix this switch because of space limitations in the sd card. Look into the sd slot and if you can see the switch , use a needle to pull the little tab down toward the base of the camera by about 2mm or until it works being careful not to bend it.

If this does not resolve your problem , there might be a short in the switch circuit and the camera will need to be disassembled to resolve this error. This should cost no more than $50.

Please feel free to contact me if you need further information

Kind regards
Andrea

Dec 14, 2010 | Vivitar ViviCam 5024 Digital Camera

1 Answer

Printer wont read SD cards does read sony memory


If it does not seat (fit) properly, why say the printer will not read SD cards? It certainly will read SD cards that are supported. You can still upload to computer and print from there as you suggested.

Dec 27, 2009 | Canon PIXMA iP6700D InkJet Photo Printer

1 Answer

Copy from camera to SD?


Create a folder on your computer desktop. Drag and drop the video file from the card to the folder. Open the folder, right-click the card, click on open with, and choose a player to open the video. If you don't have one on your computer, Quicktime is a free download and works very well.

Oct 09, 2009 | Polaroid i633 Digital Camera

1 Answer

Cannot copy photos from my SD card


If the printer is connected to your PC with the USB cable then as soon as you insert the SD card in the slot it acts as a drive. Open up "My Computer" and search for the new drive (e.g. E: or I:). You can explore the SD card as you would with your hard drive and you can copy the photos on the SD card to your computer as you would normally copy files.

Apr 05, 2009 | Brother MFC 210C All-In-One InkJet Printer

1 Answer

Printer will not read SD card from Panasonic Lumix DMC TZ3


Put the card in an adapter or in your computer. Make sure the pictures are not in folders. The printer is unable to read them if they are.
Also, the file size of the picture cannot be over 8 MB and the image size has to be below 12 megapixels.

Jul 16, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

3 Answers

Micro SD card


Open your computer scan w/ anti virus that SD card /try insert again to your printer .

Jan 05, 2008 | Epson Stylus Photo® RX620 InkJet Printer

Not finding what you are looking for?
HP Photosmart D7160 InkJet Printer Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Ekse

Level 3 Expert

13434 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Cindy Wells

Level 3 Expert

6131 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...