Top 20
Whirlpool GT4175SPS Stainless Steel 1200 Watts Microwave Oven Questions & Answers
Microwave had burnt electrical smell a few minutes
hi,
As you mensioned the Magnetron or the capacitor of the oven is short. If the magnetron or the capacitor is short then the transformer driving the magnetron will get over heated because of the over current drain. It will finally result in failure of the mains fuse inside the oven. You have to check the fuse first. If its faulty then change the same with anew one. If the fuse again blews the you have to replace the manetron and the capacitor. The magnetron and the capacitor will look like on in the picture. Magnetron in the microwave oven produce the microwaves which heats the food.
ok
9/5/2011 6:47:21 PM •
Whirlpool...
•
154 views • 0 helpful votes
Microwave turns on but doesnt
The microwaves are produced by a MAGNETRON. Everything else can work,
but if that does not, then there is no heat added to the food.
Unfortunately it is the most expensive part of the microwave and has
nothing you can really work on.
Hope this helps.
4/29/2011 9:58:59 PM •
Whirlpool...
•
199 views • 0 helpful votes
How to replace hv diode for gt4175sts microwave
you must !!!!!!!!!! discharge the capacitor first or it will kill you !!!!!!!!! use a discharge wand then cut out old diode and resolder new one ..
ps tell me why are you replacing the power diode in 15 yrs working with microwaves ibe never seen one blow
12/2/2010 4:53:48 AM •
Whirlpool...
•
245 views • 0 helpful votes
Microwave GT4175SPS 3 runs
Most likely causes are a blown fuse in HV area of microwave or an open thermal protector or thermal fuse.
Less likely causes are failure of various parts in the HV area.
Due to the lethal dangers inherent in microwaves, servicing of these parts is likely best left to a professional. That said, if you are technically versed I can point you in the direction of some good resources for troubleshooting and repair.
10/21/2010 5:47:56 PM •
Whirlpool...
•
265 views • 0 helpful votes
There is power but it is not heating anything and
If it's making a loud buzzing like sound it's the component that sends waves through the microwave. This piece is about $120 plus they charge about $65+ to install it. Also some charge the diagnostic fee of about $75. Either way, once a microwave goes out it's pretty much useless to repair one unless you have put a lot of money into it. We had ours to do the exact thing you describe and it was cheaper to buy another and me install it basically because I was getting another 2 year warranty as to the other had run out.
6/27/2010 5:16:37 PM •
Whirlpool...
•
193 views • 0 helpful votes
Whirlpool gold microwave gt4175sps - problem: will
Hi,
It sounds like there may be a diode or relay on the control that has failed. This could cause both symptoms you are explaining here. In either case the control board/keymembrane would need replaced. The cost of these would be about $173.00 for parts. Unfortunatly this repair would most likely cost more than the value of the product. Sorry for the bad news.
4/18/2010 3:43:58 AM •
Whirlpool...
•
716 views • 0 helpful votes
In order to start the microwave i have to push the
The door switch is loose or fualty you can adjust the switches first to see if it hase just moved if this does not work then replace it.unplug the unit and remove the cover panel look between the controll panel and the cavity on the back of the front panell you will see two or three switches the (GREY or BLACK ) look for the retaining screw loosen slightly and adjust if this does not work the take notes of the wire positions etc on the switch get a new on eand replace close unit plug and play
12/29/2009 3:43:43 AM •
Whirlpool...
•
118 views • 0 helpful votes
How do you install a built in whirlpool microwave
Whirlpool customer
service is here and you can also enter your
model number on that page to download your owner's manual, installation
instructions, etc.
We're
happy to help you with free advice and we'd appreciate your thoughtful
rating of our answer.
11/23/2009 8:36:24 PM •
Whirlpool...
•
274 views • 0 helpful votes
I have a Whirlpool Microwave that runs when I open
Remove the case and confirm that the door latch switch is mechanically intact. Next, disconnect the switch and test it with an ohm meter to see that it is actually working. It should show a short (0.0 ohms) when the door is closed and no reading when the door is open. Those readings could be reversed but there should be two distinctly different readings when testing the switch. If you don't see any differnce between readings when the door is open or closed then replace the switch. This should solve your problem.
10/16/2009 10:57:11 PM •
Whirlpool...
•
274 views • 0 helpful votes
The door on my Whirlpool
If the metal of
the oven is chipped or charred, it will have to be sanded smooth and
clean and dried thoroughly.
Then you can apply some
high-temperature appliance paint, available from places like Wal-Mart,
Lowe's or Builder's Square.
Otherwise, you may get rust and/or arcing.
We're
happy to help you with free advice and we'd appreciate your
thoughtful rating of our answer.
1/26/2009 7:52:59 PM •
Whirlpool...
•
181 views • 0 helpful votes
Door button broken
It may be the lever behind the door open button, but either way, you can find helpful exploded view diagrams and order parts by entering your model number here: http://tinyurl.com/gv383
Your model does not show up, but you can check GT4185 to see how the parts work.
If you or a friend decide to work on it, we have *critical* safety, disassembly, and troubleshooting info at our site, which is linked at our listing here on FixYa: http://tinyurl.com/yzjozk
8/30/2007 5:51:40 AM •
Whirlpool...
•
587 views • 1 helpful votes
Not finding what you are looking for?