Canon CanoScan - Answered Questions & Fixed Issues - Page 9

can i download driver canonscan D646U ex, where ??
thanks

Remove the glass using a knife to remove the the gray plastic on both sides and in front. They are held in place with double-sided tape. Clean the inside of the glass with rubbing alcohol. Also clean the insides of the center track and the silicon bumps on both sides of the scanning wand. put a tiny amount of spray silicon on a Q-tip and run it up and down the insides of that center track. Use the Q-tip again to wipe the silicon bumps. put it back together and there you go!

Its the right solutionWorking Great !Thanks !

the only successful method I found for using CanoScan D1250U2F in 64 bit Windows 7 (I guess the same would be for 64 bit Vista) is to use Windows XP Mode in Virtual PC (attach the scanner as USB device and that's it - works perfectly)

I had a problem with Windows 7 detecting the device as CanoScan (needed for Windows XP Mode to detect is as USB device and allow attach) - the solution was to unplug the scanner, plug it in and CANCEL Windows 7 hardware detection process before it finishes - this leaves it as "CanoScan" device (auto-detect will leave it as "Unrecognized device" and with that unusable/un-attachable in Windows XP Mode)

latest versions of Windows XP Mode will make your hard drives accessible as network locations (no need for external media)

If you do not have the disk you must download the software from Internet, follow instructions below,

Click here:Official Canon Drivers and Software

A web page will open, follow instructions, select model, select operative system etc., and click on download .
Chose to download the file in my documents when asked.
After downloading, find thefile,doubleclick on the file, if you get introubles,then follow the instructions below to reset and reinstall:

• Unplug USB.
• Download driver from website and run the file.
  
• Follow driver installation wizard.
• Plug back printer when prompted from installation wizard.

Note:some device does not work on Vista.

I was getting the same problem until I realised that this is powered from the USB port. I was also getting a core dump when trying to access it from Linux. Try reducing the length of the USB cable from the scanner to the computer and/or use a different USB port. The length of the cable is significant because the volts drop over even a short cable could cause problems. When I had this issue, I had a very long USB cable and it was coming up with error after error, when I used a much shorter one, the problem went away.Good luck and best wishes,Martin

try this Web site just pick out your scannerhttp://www.canon.ca/inetCA/suppdrv?m=goSeries&type=C&id=4

The video file contains when changing the extention .mp4 into .pdf the complete manual.

Hi - I believe that the LIDE 25 is not supported in WIndows 7. I've run into the same problem and found this out. The Canoscans that are supported are the LIDE100 and up...

Hello here is a user guide:http://www.usa.canon.com/app/pdf/scanner/PIFS36PC.pdfYou need adobe reader to read the content.Here is the software page:http://software.canon-europe.com/products/0000431.aspGood luck

Hello download the software here at canon:http://www.usa.canon.com/cusa/support/consumer/scanners/canoscan_series/canoscan_lide25#DriversAndSoftwareBut first select your windows system.Good luck

There is no power button on mine. It gets its power from the high speed usb so it is always ready. Every time I boot up my mac I hear the scanner go thru a warm up scan. I have downloaded the twain plugin for photoshop and access it that way. The lamp will go on when you preview scan something.

Hello try to reinstall the software for the scanner from here:http://www.usa.canon.com/cusa/consumer/products/scanners/film_negative_scanners/canoscan_lide_700f#DriversAndSoftwarePlease select your windows system 32 or 64 bit.Download the driver and uninstall the old software before you install the new.Canon does make an driver upgrade once a while to fix previous problems with the software.Hope this will help you

Canon knowingly disabled Windows 7 support for all of the old products in 2009. You need a pre-Vista CanoScan toolbox version 4.1.3.5, it will work fine in Windows 7. I uploaded a copy on my website rust.mine.nu.

CNQU110

You may download the software from here.

You may have luck with this WEB site. VueScan 9 scanner driver - compatible with over 1750 scanners http://www.hanrick.com/

'Tain't necessary. And not getting the part can be an improvement. I cut out a cardboard template that allows me to scan 10 slides rather than the 4 of Canon's official slide adapter. All the Canon part does is position them precisely so cropping and rotation are automatic. With Photoshop skills (File ' Automate), you can do the same yourself for whatever size. I ended up doing Brownie, 35, and 126 (gasp!) also. For extra credit, make your adapter(s) out of genuine plastic rather than whatever cereal box you have lying around.

In the Advanced tab for the scanner software, there is a tab labeled Color/Colour. On this tab, select the "Reset" button. This should return all color adjustment options to their default setting. If this does not resolve the issue, you may want to try reinstalling the software, but there is also a possibility that the unit itself has some problems.

Hello yes they have software for windows 7:http://www.usa.canon.com/cusa/support/consumer/scanners/canoscan_series/canoscan_3000ex#DriversAndSoftwareSelect your windows 32 or 64 bit and download the driver.Good luck