20 Most Recent Canon CanoScan D1250U2F Flatbed Scanner Questions & Answers


driver canon f91500 http://www.nodevice.com/driver/CanoScan_N340P/get36948.html

Canon CanoScan... | Answered on Sep 29, 2017


It depends upon the cord you need, as the scanner will have to. If you take it to an office supply, they can hook you up.

Canon CanoScan... | Answered on Jun 05, 2015


" I can only select platen as the sourc. the film setting has vanished" - I had the same problem. Unplugged the USB cable from a shared usb 2.0 hub and plugged into an old USB 1.1 dedicated port and it started working. No ideas why (perhaps in the hub it couldn't detect the scanner model correctly)

Canon CanoScan... | Answered on Mar 24, 2014


how can i download this driver software

Canon CanoScan... | Answered on Jul 16, 2013


the only successful method I found for using CanoScan D1250U2F in 64 bit Windows 7 (I guess the same would be for 64 bit Vista) is to use Windows XP Mode in Virtual PC (attach the scanner as USB device and that's it - works perfectly)

I had a problem with Windows 7 detecting the device as CanoScan (needed for Windows XP Mode to detect is as USB device and allow attach) - the solution was to unplug the scanner, plug it in and CANCEL Windows 7 hardware detection process before it finishes - this leaves it as "CanoScan" device (auto-detect will leave it as "Unrecognized device" and with that unusable/un-attachable in Windows XP Mode)

latest versions of Windows XP Mode will make your hard drives accessible as network locations (no need for external media)

Canon CanoScan... | Answered on Feb 13, 2013


Hi,
Welcome to Fixya. Unfortunately it is impossible to use the CanoScan D1250U2F to windows 7 because it is not compatible. Canon stated that the scanner is not compatible with the said Operating System. Please check the link below about the Windows 7 Compatibility.
Windows 7 Compatibility
Thanks for using Fixya.

Canon CanoScan... | Answered on Aug 21, 2011


see inside usb port & check all four pins are up or not. if pins down then put it up or replce usb connector.

Canon CanoScan... | Answered on Jul 11, 2011


drivers for canon canoscan D1250U2F......go to ... canon.ca

click on drivers for scanners and pick the model you want them for..
if you are in canada make sure that you click on drivers available in canada..

Good luck ...Jake

Canon CanoScan... | Answered on May 19, 2011


The official link with all the details for your scanner is at this link. You can also use this link to view (and save) the quick start guide (30 pages).

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Thanks and regards
Please kindly rate this solution
Stelios
direct fixya link: http://www.fixya.com/users/technical114

Canon CanoScan... | Answered on May 14, 2011


you need to release the lock switch.
have a look here about how to do it

Canon CanoScan... | Answered on May 11, 2011


I have many years experience repairing Canon scanners so here is my suggestion for you.

This is a common problem with all Canon scanners. If you do a lot of scanning or leave your computer on all the time and never shut it off. What is happening is the memory fills up with all of the images and it needs to be cleaned out. If you reboot (restart) your computer it will clean out the memory and your problem will go away. I always recommend that if your going to be scanning a lot then do it off a fresh reboot and you should be able to your hearts content.

I hope this helps you out.

Canon CanoScan... | Answered on Apr 01, 2011


You may need to re-install the drivers for the scanner. Even though it is plugged in, if the computer doesn't recognise it then it won't scan. You can get the drivers here.
Just choose your operating system and it will take you to the appropriate drivers. I see there is also toolbox software for this scanner located on the same downloads page.

Canon CanoScan... | Answered on Mar 09, 2011


Select Windows XP as the operating system

http://www.cusa.canon.com/cusa/support/consumer/scanners/canoscan_series/canoscan_d1250u2f#DriversAndSoftware

Click on link below to read more on how to get your Canon CanoScan to work with Windows 7

http://www.tomshardware.com/forum/240604-45-twain-scanner-driver-canoscan-d1250u2f

Canon CanoScan... | Answered on Oct 18, 2010


1. Uninstall all the drivers
2. Power cycle your computer
3. Re-install all the drivers
4. Finally re-connect the scanner

Canon CanoScan... | Answered on Aug 14, 2010


make sure you have an installer compatible for mac os if not you can download on the internet. :)

Canon CanoScan... | Answered on May 30, 2010

Not finding what you are looking for?
Canon CanoScan D1250U2F Flatbed Scanner Logo

47 questions posted

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

old marine
old marine

Level 3 Expert

2254 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

CanoScan Canon

  • CanoScan Canon

Most Popular Question

cord needed

  • Office Equipment & Supplies
Loading...