At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: When I plug in the cable the power light comes on for...
If this has been sent to you by your ISP when you joined, ring them and tell them its stopped working and the should send you a new one.
It sounds like some circuitry has died, replacement required.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If it is still in warranty call the manufacturer.
if not give more info [email protected]. May be somthing simple like a cable
shutdown computer unplug then disconnect the video cable on the computer from the monitor, plug monitor back in and turn it on, there should be a display that says no video source within a few seconds, if unit is working properly. shutdown and connect video again and then reboot computer. sometimes it just takes a compleat power disconect to reset things,
* try connecting ur belkin router to different power socket
* try with different power adapter
* or else press the reset key for more than 1 min
while holding the reset unplug the router power cable and plug it back again 3 times.--- while holding the reset u shouldnt release the reset while u unplug and replug.
the interval between each unplug and replug should be 15 seconds.
* then release the reset then unplug the power cable and plug it back
* it has to work or else replace it with the belkin tech support
tv works for about 2 minutes, then shuts itself off. the red standby light flashes 50 times, then the tv. comes back on for approximetly 2 minutes then goes off again, only to repeat again
you have problem wit the lamp just plug in another once you removed the back cover and if the lamp stays on the it is 100%. you do not need original lamp. Any 15" lcd lamp that fits will do the job. HA HA well done
Ahmad
COMPBITS.COM.AU
no problems man
:just take out the catriges..plug outthe power cable ....then plug it bacvk in after 20 secnds,the printer will ask fr printer catriges ,puthem back in and try to perfom fnctions ,still problem persists ,follow following steps
:just go ahead and take ou the power cable
and press and hold # and 3 fr 30 seconds
while pressing them plug in the power cable
:similarly perform with # and 6
:ur problem will be resolved
Be sure that your Modem plugs into the WAN port on the router.
1. Unplug your cable/dsl modem power 2. Unplug your Router power 3. Plug in your modem power ... wait for it to come completely up. 4. Plug in your WRT54G Router and wait for it to come up.
Press the reset
button on the back of the router for 45 seconds while it is powered on. This will do a factory reset. Wait for it to come up. Then unplug it. Wait 30 seconds and plug it back in. Let it come all the way up.
Plug a PC into one of the switch ports on the router. Now do an ipconfig /release and ipconfig /refresh in the command prompt of your PC to get an IP address from your Router.
Now you should be able to ping 192.168.0.1 and you should be able to get into the the configuration utility by putting http://192.168.0.1 in a browser. The username should be blank and the password will most likely be admin (all lower case).
Be sure to lock down your wireless SSID
so neighbors and people passing by are unable to connect to your access
point and do bad things on your network.
The first thing in this unit is to check the ribbon cable that goes from the front control panel to the back ssb board, I would unplug and replug to make sure seated properly. Then try it again. There are alot of screws to take out but worth it if this solves the problem.
This is the typical way that drive belt problem occur. The
mechanism needs some slip to accomodate the changing reel speeds as the
tape plays, but if it slips too much, the reels don't move at all, the
processor thinks there is a problem and turns off.
Time for a belt job.
×