Linksys Computers & Internet - Recent Questions, Troubleshooting & Support


just fixed one yesterday.
the power pack was no good.AC wall wart,
power green LED blinked endless. and the white logo, LED is dead..
a new pack fixed it.
also the wrong pack used, ! do not mix them up. oops.
first year 54G, v1 uses 5vdc pack.
at v2, and up all want to 12vdc pack,
bottom sticker on above failed was v6.
you said recognized, does that mean the 4 rear Ethernet wired jacks are dead, or just wifi dead.?
first the ethernet ports must work, or wifi is doomed.

Linksys... | Answered on Feb 18, 2020


Good day,
This might be of help .
Steps To Fix Linksys Router Error 321:-
Step1:- Check the Firewall Settings
To check the Firewall Settings is the first priority for the users. Then check the firewall settings of the computer/ Laptop, will be helpful to find the problem. If there is any firewall installed on the computer, so the users need to turn it OFF.During the process, the users ensure that the Local Area Connection on the computer is not disabled. The Local Area Connection should not have any static IP address assigned. If there is any then the users need to immediately set the IP address to automatic.
Method2:- Run the Installation CD Again:-
The users require trying to run the CD again and ensure when the CD runs, it will ask to connect the computer and the modem to the router with the cable. So the users will need to notice, that there all the lights lit up on the router. If it's not, then users will need to setup their router without the CD.
The users can get the instruction to setup router manually in the method 3.
Step3:- Try to Setup Router Without Installation CD
Setup Linksys Router without Installation CD is another best option for users in order to completely avoid the in order to fix Linksys Router Error 321.
Follow the below-given instruction to Setup Linksys Router without Installation CD:
First of all, connect the main computer to the Ethernet port on the router.
Then the users need to connect the modem to the Internet port on the router.
Now it's time to verify the status of the light that is blinking properly.
Next, users need to open the setup page of the Linksys Router and then change the Internet connection settings manually.
In the setup page of the Linksys Router, the users can change the settings of the router as per their needs.
Then the default IP address of many Linksys router is 192.168.1.1. And the default username and password would be an "admin".
Wait for a few minutes, when the main computer is able to access the Internet, so users need to create a wireless network for their wireless computers/devices.
or you can call them @ Toll Free 1-800-204-6959 that is Lynksys support.

Linksys... | Answered on Feb 03, 2020


The following routers are the only models that support the AOL Broadband Cable service. Note: All Linksys routers support AOL DSL connections due to the standard PPPoE login and authentication connection type used with that service. Please be sure to check the version number of your router (which can be found on the underside label). Only the specific models and versions listed here are supported by AOL Cable: * BEFW11S4 * BEFW11S4 v2, v3, and v3.2 * BEFSR41 * BEFSR41 v2 * BEFSR11 * BEFSRU31 * BEFSR81 * BEFSR81 v2 * HPRO200 (Available from AOL only at this time) You must Enable the "AOL Parental Controls" option located in the Security tab of the web-based Setup utility pages of these routers in order to get a connection using AOL Cable. You may access the utility by visiting http://192.168.1.1 in a web browser and by logging in using the router's password (by default, the password is admin).

Linksys HomeLink... | Answered on Jan 29, 2020


Step 1 : Connect - Router - Computer ( Wired )

Step 2 : open Router Setup by typing http://192.168.1.1 on the address bar of internet explorer

Step 3 : Default password is admin

Step 4 : Click wireless

Step 5 : Choose wireless security

Step 6 : Here you can find the Password

Step 7 : Try to connect with this password

let me know if this works

Regards
TOM

Linksys... | Answered on Jan 28, 2020


There are several factors that will affect or can cause problems in connecting your Roku to your Router.

If you're getting an error message on Roku like 014, 011, make sure to indicate it in your response. Normally, if you're getting 014 message, you can follow these steps:

. A simple power cycle resolves most of the issues. To perform a power cycle, please follow the instructions below:

1. Unplug the power cables from the modem, router and the Roku player.
2. Connect the power cable to the modem (after a minute). Once all the lights on the modem are lit, plug in
the power cable to the router and then to the Roku player.
3. Go to "Settings" and redo the complete Roku setup.

If the issue continues to occur, please try the channel 1 or 3. Should it persist, you may reset the Roku
player. Here is how:

On the back or bottom of the Roku unit, you should find a recessed little hole.
- Use a pin or paperclip to press and hold the button for 30 seconds (please ensure that the power light
blinks while you are holding it down).
The Roku device will reset to default and be ready for setup again.

If the problem continues, please reflash the software via the secret screen:
1. Press the "Home" button for 5 times.
2. Press the "Forward" button for 3 times.
3. Press the "Rewind" button twice.
4. Choose Update Software and the Roku player will then restart.

You can comment your serial number or the error message that you're getting. If your getting 011, just power cycle your entire network. Also, please make sure that you're not connecting the Roku to a Guest network. The speed of your connection matters as well. It should be atleast 1.5mbps.

Linksys... | Answered on Jan 27, 2020


https://www.linksys.com/ca/support-article?articleNum=140923

Which model?
Go to the Linksys website and download the instructions for your model of extender.

Linksys... | Answered on Dec 02, 2019


Access your router Setup page 
Open internet explorer go to http://192.168.1.1 (default) username: admin (default) password: "leave it blank" (default)
Go to Security go to Filter
if you know that Ipaddress of the computer you want to block for example 192.168.1.10
You can create up to five different IP Address Range filters   Users who have  filtered  IP addresses will not be able  to  access the  Internet at all   If you only want to filter one  IP  address instead of a range of IP addresses, enter the same  value into both fields  For instance, if you wish to filter the  PC with  the  IP  address of 192 168 1 5, enter 5  into both  fields on one line: 192 168 1 5 ~ 192 168 1 5 

if you know the MAC address of the computer click the Edit MAC Filter Setting and input the MAC address you want to block. 
blocking by MAC address is the most effective solution to block a computer... while blocking by ip address will be easily bypass by changing the ip add of the pc

then saved your settings and reboot..

Linksys BEFSR41... | Answered on Nov 27, 2019


Control Panel->add or remove programs-> Intel(R) PROSet/Wireless Software -> Modify -> Unmarked WI-FI PROTECTED SETUP

Linksys... | Answered on Nov 25, 2019


The vent actuators are bad. there should be two. one on each side. they are small toy like motors that open and close the vents from within to allow the hot air to blow by closing the vents to the a/c unit.

Linksys... | Answered on Nov 21, 2019


You can get best linksys router support phone number at Toll Free Number ( 1-877-769-0969 ). Linksys router Tech Support number ( 1-877-769-0969 )

Linksys... | Answered on Nov 12, 2019


DO NOT CALL FAKE NUMBERS OR GO TO FAKE WEBSITES

Linksys... | Answered on Nov 11, 2019


this ones for you loser

Linksys... | Answered on Nov 10, 2019


Linksys router not support to work with landline.

Linksys router only can work with cable internet.

Linksys... | Answered on Nov 07, 2019


If you already have a cable router, then you don't want to use a wireless router. You will want to use a wireless access point instead.
The reason for this is that anything plugged-in to your cable router will not be able to access anything connected to the wireless router due to the NAT firewall in the wireless router.
If the wireless router has the option to make it a "Gateway", then that will fix this issue; otherwise, take the router back and buy a wireless access point instead.
As for how you hook up the wireless router to the cable router, you have to unplug the power cord of the cable router for about 15 minutes before hooking the Ethernet jack from it to the wireless router.
Once the 15 minutes have passed, you then can plug the Ethernet cable from the wireless router "WAN" port into an Ethernet port on the cable router and then plug-in the power cord of the cable router.
Once the cable router is finished syncing-up, the cable router should provide an IP address to the wireless router.
If you really have a cable modem instead of a cable router, then you won't have to put the wireless router into gateway mode.

Linksys... | Answered on Nov 02, 2019

Not finding what you are looking for?
Linksys Logo

Family Lines

13,666 questions posted

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...