Printer won't work, saying a B200 error but can't find what that

I Know this B200 Error.

Canon Printer Error B200 has been used very commonly by Canon Printer customers. The positive point, though, is that there is a procedure that you can pursue to handle and correct this error.

Canon Printer Error B200 on canon printers means that printing head voltage or printhead heat is not natural. In certain cases, Canon Printer Error B200 can either indicate that the print head has been broken and should not be used or that there is an issue with the cartridges.

Easy Solution of Canon Printer Error B200:-

1. Switch off the printer. Remain until the cartridge carrier returns on the side.
2. Switch On the printer.
3. Extract the cartridges. Check the nozzles and brush them if there's any clogged or dried ink.
4. Reinstall the cartridges.

Contact here - Canon Printer Error B200

Thanks For Reading

The Canon service info is:
B200/P10 - Orange and green light blinking 10 times Description: A service error has occurred. Resolution: 1. Turn off the printer. 2. Disconnect the power cable. 3. Open the printer cover. 4. Check for any orange protective tape or white polystyrene and remove if necessary. 5. Check that there are no foreign objects in the printer (such as a paper clip) and remove if necessary. 6. Close the cover. 7. Reconnect and turn on. If the above solution has not resolved your error, please contact your nearest Canon authorised service facility using the link at the top of the page.

The error code is usually given for a foreign object present in the print head carriage path, so check at both ends for a crumpled up wedge of paper. If nothing is found, it is most likely that your print head has an over-heating problem and is dying

B200 means VH monitor error, your bring it to service center for repair. In most cases - defective control board

If your all cartidge is not fully loaded on ink than showing the error.

canon ip 2770 eror b200

Try keeping the paper only in the bottom tray (there's a tray in the bottom) Try pulling any paper out of the top and just close that top tray. Open up the head so that u can see the ink cartridges and turn the printer on and off and maybe it will center itself again. If it's still not working (even if lights aren't red and print head wont align in the center) try manually moving the head back and forth like 18 times so you can lubricate that rail in the back that's holding it. After that, re-turn it off and on again.

orange light blinking 

Search Results for ORANGE 5 AND GREEN 1 <<Previous 30 results Next>>
1. Power light (or Alarm and Power lights) alternate(s) between orange and green
After long green flash, there are 2 or more alternating orange and green flashes. There may also be a Service Error message on the computer screen. 2. Alarm / Power light flashes orange 11 times consecutively (Automatic Print Head Alignment Error) 3. Alarm / Power light flashes orange 2 times consecutively (Load Paper / Paper Feed Error) 4. Alarm / Power light flashes orange 3 times consecutively (Paper Jam Error / Cover Error) 5. Alarm / Power light flashes orange 4 times consecutively (Out of Ink Error) 6. Alarm / Power light flashes orange 5 times consecutively (Print Head Error)
#1 & #6 seem to be as close as I can find:
here is the page (Below) if you just put the error in the space provided.

http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=257&modelid=10239

Try this:

Pull the power cord out of the back of the printer.

Then move the printhead to the center and pull out the ink and the printhead. Clean the printhead and examine the bottom for burned areas.

With the printhead still out, close the cover and plug the power in and turn the power on. If your printer isn't damaged, it should go through all diagnostics and give you a solic green light. This means you probably need a new printhead.