I have a Xerox 8560MFP printer with the following error code. 07010.43:39050 Any help would be appreciated

Hi Anonymous,
You need to contact your the www.xerox.com website.
Regards.

Here's what I found in my service manual
37,0XX.xx PEST Heater Faults
An heating error has occurred. The following troubleshooting procedure applies to these errors:
37,002.47 The Left Jetstack is drawing less power than expected.
37,003.48 The Right Jetstack is drawing less power than expected.
Now my service manual was written 4 years ago. I couldn't find the specific code you listed above, but these seem to come closest to answering your error code.

On the Xerox 8560MFP multifunction, this error code 39,003 signifies a Scanner problem, specifically that the Optical Test has failed. the 75554 is your current page count on the printer.
The Scanner Assembly 062K22590 must be replaced. It is fairly expensive, but moderately easy to replace.
You should also order the Scanner Calibration Sheet 109K01910 to make sure that margins and contrast are correct.
The scan/ document section is broken into 2 main parts, the Scanner, and the Automatic Document feeder. The feeder section is probably working fine.
Good luck with that.
Whit Item, Inc. Alexandria, VA

There is a problem with the power up of the printer. For 37,00x.xx error codes you can try power off the printer, wait 30 seconds and power it back on. According to the Xerox website for 37,008:44 error code you should Verify the Printer's Power Source and Isolate the Printer.

any error code show please send me details

Hi mary_ballling:

Here is you problem.

9,035.4x through 9, 038: Fault codes associated when ink count flags are stuck
after melting 2.5 ink sticks. The following codes are recorded: 9,03x.41, where x= 5
for cyan, 6 for magenta, 7 for yellow, and 8 for black.

Troubleshooting Procedure
Step Questions and Actions Yes No
1 1. Are the ink sticks all Xerox ink? Go to Step 2.
Run clearISCfault test to clear the error.
2 1. Manually verify that the ink stick is able to
advance in the ink loader chute.
Go to Step 3.
Remove any blockage and/or replace the ink stick.Run
clearISCfault test to clear the error.
3 1. Run the appropriate Ink Melt [1, 2, 3, 4]
Heater test.
1 = Yellow
2 = Cyan
3 = Magenta
4 = Black
2. Did the test pass?
Replace the printhead.
Replace the ink loader assembly. Run
clearISCfault test to clear the error

Hope this helps

09,03x 35 = Cyan 36 = Magenta 37 = Yellow 38 = Black The error indicates an ink stick was jammed. You have to clear the ISC (ink stick count) error. Turn off the printer. Turn on the printer. As soon as you see XEROX start moving across the display hold down the back and help buttons until you see "beginning service mode" on the display. Release the buttons, it will now come up in the service mode. Scroll down to the function menu, hit ok, scoll to clear isc faault, hit ok. Hit the back button to get back to the first menu then exit diagnostics, hit ok when it asks if you want to restart in customer mode.

there is a stainless steel print head block on the lower back portion of the frame that gets contaminated with spill over ink from the catch tray. That causes the print head not to move properly.
The wiper blade may also be tacked to the print head.
That code means the print head is not moving into the print position properly.
That stainless steel block is about 1 inch square.

One of your ink sticks is not moving down into the ink loader properly.Either one is cracked, twisted or otherwise not moving down the loader. I think the .46 means its a black stick.

If powering Off & On didnt work.

Than we need to reseat the HDD.

Follow the steps mentioned on the link:

http://www.support.xerox.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=384,E=0000000001218712366,K=3033,Sxi=8,Solution=obj(6029)