Which connectors on rear are audio out? - Sharp AQUOS LC-60C6400U 60" 1080p LED-LCD TV - 16:9 - HDTV 1080p - 120 Hz ATSC - 176AAAA / 176AAAA - 1920 x 1080 - Surround Sound - 4 x HDMI - USB - Ethernet - Wi-Fi - PC Streaming - Internet Access - Media Player

Try users manual:
http://audio.manualsonline.com/manuals/mfg/yamaha/htr5930.html?idRes=237094

10 pins connector black..................GRN yellow.................BATTERY Blue....................IGNITION OR ANTENNA PWR FRON RADIO 4 pins connector purple..................REAR R (+) purple/black ........REAR R (-) green...................REAR L (+) Audio in................RCA jacks
green/black..........REAR L(-)

42PG20 Connections

• Connector Type
  
• 1 x Composite video/audio input ( RCA phono x 3 ) - Rear ,
  
• 1 x S-Video input ( 4 pin mini-DIN ) -
• Rear , 1 x Digital audio output (optical) ( TOSLINK ) - Rear ,
• 1 x Remote control ( Mini-phone 3.5 mm ) - Rear ,
  
• 1 x Serial ( 9 pin D-Sub ) - Rear ,
  
• 2 x Component video input ( RCA phono x 3 ) - Rear ,
  
• 2 x Audio line-in ( RCA phono x 2 ) - Rear ,
  
• 2 x HDMI input ( 19 pin HDMI Type A ) - Rear ,
  
• 1 x VGA input ( 15 pin HD D-Sub (HD-15) ) - Rear ,
  
• 1 x Audio line-in ( Mini-phone stereo 3.5 mm ) - Rear ,
  
• 1 x Composite video/audio input ( RCA phono x 3 ) - Side ,
  
• 1 x HDMI input ( 19 pin HDMI Type A ) - Side

42PG20 Audio System

• Sound Output Mode Stereo
• Surround Mode Yes
• Sound Effects SRS TruSurround XT
• Audio Controls Bass , Treble , Balance , Sound mode
• Speakers Included 2 speakers
• Output Power / Total 20 Watt
• Additional Features Auto volume adjustment
• Speaker(s) 2 x Right/left channel speaker - Built-in - 10 Watt

the connector is marked F_audio and it is located directly behind the rear facing audio jacks. should be only one plug either marked "hd audio" OR "ac97 audio". some cases are setup for either, but you only need one of them depending on what your motherboard supports.

11) F_AUDIO (Front Audio Connector)
This connector supports either HD (High Definition) or AC97 front panel audio module. If you wish
to use the front audio function, connect the front panel audio module to this connector. Check the pin
assignments carefully while you connect the front panel audio module. Incorrect connection
between the module and connector will make the audio device unable to work or even damage it.
For optional front panel audio module, please contact your chassis manufacturer.
By default, the audio driver is configured to support HD Audio. To connect an AC97 front panel
audio module to this connector, please refer to the instructions on page 72 about the software
settings.
Pin No. Definition
1 MIC
2 GND
3 MIC Power
4 NC
5 Line Out (R)
6 NC
7 NC
8 No Pin
9 Line Out (L)
10 NC
AC'97 Audio:
Pin No. Definition
1 MIC2_L
2 GND
3 MIC2_R
4 -ACZ_DET
5 LINE2_R
6 FSENSE1
7 FAUDIO_JD
8 No Pin
9 LINE2_L
10 FSENSE2

yes, you must have at your tv one of this plugs: Connector Type Sony DVP-NS710H 1 x Composite video output ( RCA phono ) - Rear , 1 x HDMI output ( 19 pin HDMI Type A ) - Rear , 1 x Component video output ( RCA phono x 3 ) - Rear , 1 x Audio line-out ( RCA phono x 2 ) - Rear , 1 x Digital audio output (coaxial) ( RCA phono ) - Rear on your tv the connector is input.

NO> If your TV supports and have HDMI connections and your HD receiver has an HDMI output then you should have no problem displaying Video. Just make sure you change the input signal of your television to HDMI input. After looking at the spec's of this model these are the following inputs you have. your best picture quaity would be to use componet cables instead, which can show full screen 1080i format, your television does not show at 1080p whis is what HDMI is known for.
Connectors
Rear Input Connectors S-Video x 2 - Component x 3 - Composite x 2 - DVI x 1 - RF x 2 - 1 x RS-232C - Audio (RCA) x 6

Front Input Connectors S-Video x 1 - Composite x 1 - Audio (RCA) x 1

Rear Output Connectors Composite x 1 - Audio (RCA) x 1 - RF x 1

Another good option is use to use a DVI to HMDI connector and hook it up this way. But note: you will have to use audio cables for the DVI input.

Try the Audio 1 rear. With the headphones plugged in on some T.V.s the headphone jack unfortunately disconnects the audio from the other outputs. Try looking in the documentation to see if you can change this in the T.V.s menu as some allow you to use both for hearing impaired people. Hope this helps.,

These are all the connectors on the back. The "1 x component video output" indicates that you can use the "3 color video cord" you have, better known as Component Video Cable.

Connector Type: 1 x HDMI ( 19 pin HDMI Type A ) - rear ¦ 1 x component video output ( RCA phono x 3 ) - rear ¦ 1 x S-Video output ( 4 pin mini-DIN ) - rear ¦ 1 x composite video output ( RCA phono ) - rear ¦ 1 x audio line-out ( RCA phono x 2 ) - rear ¦ 1 x 5.1 channel audio line-out ( RCA phono x 6 ) - rear ¦ 1 x digital audio output (coaxial) ( RCA phono ) - rear ¦ 1 x digital audio output (optical) ( TOSLINK ) - rear ¦ 1 x network ( RJ-45 ) - rear ¦ 2 x USB - front

as far as your first question it is possible. there may be an option in the bios. if not. you can bust out the soldering iron and solder the lines for you frontal mic port to the card.maybe put some sort of connector inline

and for your second question. there is no way. unless you upgrade your sound card. although i do have a logitech 5.1 system that uses some sort of matrix technology to emulate surround sound out of a standard stereo input. cost me 60 bucks and works great

T0X1K66O
Owner, Founder, Head Technician
Leading Edge Computers LLC
[email protected]

I had the same problem, and it went away when I connected the the front speakers via the 'ac97' connector from the case, instead of the HD audio connector. It seems using the HD audio connector, as well as using no connector and forgetting to put back the jumpers originally set over 2 of the front audio connectors pins, will cause no audio from the back ports.