Question about Frigidaire Washing Machines

1 Answer

Whats the difference between e10 and e11 error codes on frigidaire afinity f/l washers?

Posted by on

1 Answer

  • Official Brand Answer
  • 2,267 Answers

Thank you for your post, greg aguilar!
Both error codes "E10" and "E11" stand for fill time is too long on your Frigidaire washer. This could be an issue with the water pressure coming into your washer the psi must be above 30 psi. If it is not you may need to correct the pressure issue. If it is check to assure that the hose is not kinked or blocked. You may need to replace the water inlet valve, pressure sensor, or control panel. I would recommend having a professional technician come out to provide a proper diagnosis for repair. Hope this information is helpful to some degree. -Matt

Posted on Nov 21, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

richroth
  • 9472 Answers

SOURCE: My Frigidaire washer is reading error code

E11 = Long Fill Time
Check to see the water valves are opened all the way. Check water hose screens for buildup.

Posted on Jan 30, 2011

  • 25 Answers

SOURCE: e10 code on a zanussi jet system washer

Is it a washer-dryer? E10 relates to a fault with the inlet valve.....usually the valve itself going open circuit.

Posted on Feb 28, 2009

  • 1 Answer

SOURCE: e10 error code

1 beep and E10 is listed as the dispenser door is open. Try reclosing your soap dispenser door tight.

Posted on May 21, 2009

  • 1 Answer

SOURCE: I have a Frigidaire Gallery front load washer with E10 error code

When ours does that it is because of the hard water build up. We have to un-hook the hot water clean out the minerals and it stops doing it.

Posted on Dec 03, 2009

  • 141 Answers

SOURCE: FAFW3577KWO washer-code E11

Hi,
Your machine may have short circuit with the inlet valve since you are facing problem after 5 to 6 mins you are suppose to change the inlet valve

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

M frigidaire washer model gltf2940fs1 shows me a e11 code


Thanks for your post, friend!

From my understanding your Frigidaire frontload washer, GLTF2940FS1, is displaying an "E11" error code. Typically, "E11" stands for fill time too long which means you could have an issue within your pressure sensor or control board. I would recommend a reset on your washer and that can be done by flipping the household circuit breaker off for ten minutes. If that does not help correct the issue you may want to consult with a technician for proper diagnosis. I hope this is helpful. -Matt

Oct 15, 2014 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

WHAT does E11 meens washer does not take in water


Good Afternoon Friend,

I understand that your Frigidaire Affinity washer, model# ATF705BZHS, is not filling with water and showing an E11 error code. The E11 code means that your washer is taking a long time to fill. First, make sure that the incoming water faucets are turned on. Next, you will want to make sure that the pressure is above 30 PSI. I suggest resetting your washer, by either unplugging it or shutting the power off at your home's circuit breaker for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your washer status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 10, 2014 | Frigidaire AFFINITY WASHER ATF705BZHS FOR...

1 Answer

Error e 12 frigadaire front end loader washer


Hello paversa971 - Are you certain the error code is E12? This manufacturer does not have any E12 error code for washers. Could it possibly be E10 or E11? If so, washer may be experiencing a water fill issue.

Dec 14, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

My Frigidaire washer is reading error code E11..how do I resolve this problem?


E11 = Long Fill Time
Check to see the water valves are opened all the way. Check water hose screens for buildup.

Jan 30, 2011 | Frigidaire GLTF2940ES Front Load Washer

2 Answers

E10 on my Frigidaire Affinity Front Load Washer


just go to fridge website support center and see what the code is or google Frigidaire code 10

Jan 22, 2011 | Frigidaire Washing Machines

1 Answer

I have a Frigidaire Front Load Washer during its cycle usually 24 and 16 min into the wash cycle it will stop and beep giving a E10 error message. What does this mean?


The cause of the error is that no cold water is getting through the cold water valve (inside the machine).

The E10 error indicates that one of a group of error codes occurred. The specific code could have been one of the following:
  • E11 - Fill time too long. (See test 1 below)
  • E13 - Water leak in the tub or air leak in the air bell. (See test 2 below)
  • E14 - Dispenser drawer reed switch is open. (See test 3 below)
To recall the specific fault code from this group, follow these steps:
  1. Wake the machine by pressing any button
  2. Wait 5 seconds
  3. Press and hold the Start and Pause/Cancel buttons simultaneously
  4. All LEDs will go blank and after a few seconds the control will signal the stored code
Based on the specific error code, follow the specified test and troubleshooting.
The magnet for the dispenser drawer reed switch is shown in the second image below. If this magnet is missing, you will get the E14 code.
Some of the troubleshooting provided is intended for service technicians. Do not conduct any test or troubleshooting that you are not completely confident that you can safely complete. Unplug the washer before accessing internal components.

http://appliancejunk.com/forums/index.php?topic=1364.0
That website above directly addresses your issue.

Jun 01, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

E10 error


Hi there,

The E10 error indicates that one of a group of error codes occurred. The specific code could have been one of the following:
E11 - Fill time too long. (See test 1 below)
E13 - Water leak in the tub or air leak in the air bell. (See test 2 below)
E14 - Dispenser drawer reed switch is open. (See test 3 below)

To recall the specific fault code from this group, follow these steps:
Wake the machine by pressing any button
Wait 5 seconds
Press and hold the Start and Pause/Cancel buttons simultaneously
All LEDs will go blank and after a few seconds the control will signal the stored code

Based on the specific error code, follow the specified test and troubleshooting.

The magnet for the dispenser drawer reed switch is shown in the second image below. If this magnet is missing, you will get the E14 code.

Some of the troubleshooting provided is intended for service technicians. Do not conduct any test or troubleshooting that you are not completely confident that you can safely complete. Unplug the washer before accessing internal components.

Good Luck!!

Thanks

Jul 06, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

My washer is giving error code e10 and im not sure what to do my washer is a frigidaire front load


I have an error code chart that came with mine and it says a few different things for E10. 1st says water not entering washer. 2nd says water leaks. 3rd soap dispenser drawer is open. In another post there was something about a magnet needed in the drawer too. But I would suggest checking your hoses and making sure you have water and the drawer is completly closed.

Jan 18, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

I have a Frigidaire Gallery front load washer with E10 error code


When ours does that it is because of the hard water build up. We have to un-hook the hot water clean out the minerals and it stops doing it.

Jan 10, 2009 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Error code E10 on the electrolux ecovalve EWF1087 front load washer. What does this mean?


E10 is a timeout code. I found the answer on google by refining my search criteria. The tap was not turned on enough for the washer to fill up in time before the timeout was reached. After restarting the washer and turning the tap on further, the washer cycle completed without error.

Jul 22, 2008 | Electrolux Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

Jason Harris
Jason Harris

Level 2 Expert

264 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...