Fisher Audio Players & Recorders - Page 5 - Recent Questions, Troubleshooting & Support
Fisher equalizer 2322
"Rec" is a send (output from Fisher to an external device) and PB (playback) is a input from external devices in to the Fisher. Remember all outs feed in's, and all in's feed outs...output from Fisher (Rec) IN to EQ. Out of EQ in to Fisher (PB). A quick test is to simply jumper the out to the in and check Fisher for proper operation. Also, in these modes you MUST press the "Tape Monitor" button for the audio signal to be routed through this In/Out loop.
Fisher equalizer-2322
"Rec" is considered a send (output from Fisher to an external device) and PB (playback) would be an input from external devices in to the Fisher. Remember all outs feed in's, and all in's feed outs...output from Fisher (Rec) IN to EQ. Out of EQ in to Fisher (PB). A quick test is to simply jumper the out to the in and check Fisher for proper operation. Also, in these modes you MUST press the "Tape Monitor" button for the audio signal to be routed through this In/Out loop.
Stuck in standby mode on Fisher RS-911A receiver
Does it power up or straight to standby? If it is on but in standby it could be speaker protection issues...check speaker wires and/or speakers for issues. If it's straight to standby and no power, it's repair shop time.
Fisher ca 880 specs
There is a bad driver for the final amp. The oscillation is called motor boating. You need to take it for repairs unless you know how to solder, have test equipment, want to buy the schematic and the parts.
Installation
Dear Woman: Since you know how to use the internet, I suggest you go on line to the manufacturer/customer service. Give them the details regarding the model number/s and ask for the manuals. They may even assist you with the set up procedures.
Fisher radio TAD-9415 made in 1995
Check firstly, if your radio is Fisher Tad-9415 you are in ****! The only chance which you have it is to make it repaired by the company. The price of repairing: $750 us address I do not know it. Sorry. But, keep really because the casset reader and the radio FM always works. I would pay $1000 us to renovate this radio if I was you! I hope that you is not too much over!
Three million times sorry.
Stuck CD Magazine
You'll have to take the cover off. Look for screws around the back and on the sides. Most likely a cd is wedged in the wrong place. (not fully ejected) and is preventing the magazine from ejecting.
Different speakers
Yes You can , but remember that those speakers are fitted with this amplifier , so if You change them with bigger You may overload the amplifier , and if they are smaller they will burn.Read the sticker from the back side of the speakers and replace them with similar on power & impendance .
When i push the power button on, the only thing
Unless you feel confident opening up the unplugged unit and looking for a fuse or other simple fix, then it's time for the repair shop to take a look. ALWAYS ask for an estimate on the repair before work is done but don't be surprised if a "no-fix" will require a estimate fee payment.
11/12/2013 4:25:48 PM •
Fisher RS939
•
Answered
on Nov 12, 2013
Looking for operating manual for Fisher MC-3000...
I found one on Ebay for $5 and suggest that as the easiest. If you can find a "scanned" version online, the quality of the scan may make it useless. Also, these receivers were pretty standard back in the day so a model number similar to the MC-3000 will likely have the same info you need.
Clock
Press POWER to Turn ON the unit.
Press CD/Door OPEN.
With the Doors Open, on the Inside Right is a "Clock Set" Button... Press it once.
With the Hour blinking, press the "CD-Tuner-Skip" Up or Down Buttons to set hour.
Press the "Clock Set" Button again to make the minute display blink.
Adjust the minutes the same way.
Once the hour and minutes are both set, be sure to press the "Clock Set" button
one more time. Now the Hour and Minute display should no longer be blinking and
you should be good to go. (I just figured it out for myself.) Hope this helped!
Fisher ca 9025 amplifier
For those who accidently put thier CA-9025 in standby mode by hitting the timer button and no longer have the remote, I figured out how to turn them back on.
Turn on the power button and press and hold the Tuner button for at least 10 seconds. it should come back on :) Hope that helps.
9/18/2013 12:52:07 AM •
Fisher RS920
•
Answered
on Sep 18, 2013
Not finding what you are looking for?