Electrolux Washing Machines - Page 6 - Popular Questions, Answers, Tips & Manuals

E21 is error for water not draining fast enough.

Get warranty service if new.

Hello, I think that your drain pump is blocked of is faulty. You will need to drain the water from the machine, remove the drain hose from the drain outtlet on the wall. or sink unit. Once you have done this check that the pump filter ( if fitted) that it has not clogged with fluff or other debris, If that is not clogged, you will need to look under the machine and check the hoses from the drum to the pump for items like flimsy underwear, socks, or other small items, these can slow the water flow, stop it, or stop the impellor on the water pump. If that is not blocked. check that the drain hose to the domestic outlet is not blocked, as sometimes if you live in a hard water area, it can block with calcium deposits. I hope this helps?

Firs of all check out error code number, then check out what it's mean in service manual booklet. Can be simple problem- drain are dirty, clean up.

10E: Water level is above parameter set (10 scale units) after water discharge

Can you turn off your overdrive? When towing most vehicles have an overdrive off mode. You can’t tow in 5th or 6th gear and may confuse computer and put car in protection loop mode.

Between tub hose and drain pump.

Abnormal condition of spin-dry • The safety switch works 3 times continuously. The number window LED display abnormal code: "E3" and begin blinking on and off at the same time and the electric buzzer sounds to indicate a problem. Dado

The tachometer or tacho-generator has the function of controlling the electric motor and the speed of the motor (rpm). So, could be electric motor blocked for some reason, worn out carbon brushes, faulty tachometer, wiring and finally electronic. After 5 years working of washing machine, by my experience the most common reason is worn out the brushes of electric motor. Dado

As you say bought new suggest you contact suppliers and under guarantee should be replaced free of charge . hope still under guarantee time limits shouldn't run might cause damage ?

Family error code E10 is visible to customers and (could be E11 and E13 only visible in service mode) means problem with filling water. I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing programme). Press and hold down START/PAUSE and the nearest option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the last alarm. The alarm sequence continues as long as the two buttons are held down. Before anything first check filter on solenoid valve and filter on inlet hose. Also, check is there any water inside drum, means that last drain phase is finished and pressure switch is in empty position. E11 - Tap closed or water pressure insufficient; Drain hose incorrectly positioned; Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty¸. E13 - Drain hose incorrectly positioned; Water pressure insufficient; Water fill solenoid faulty; Leaks or blockage in pressure switch hydraulic circuit; Pressure switch faulty; Circuit board faulty. Dado

27 code is a level offset.

Ok when this happens what it is is water has leaked into the base of the washer and activated the flood switch. What you need to do is pull the washer out and lean it 45 degress backwards. This will allow the water to drain from the base so you may need a towel for that part. Once the water is out the flood switch will reset itself and clear this fault. Then see how it goes from there. But if it happens again then something is leak under there and you need to find the fault and fix it to sort it. But if you do the above then you should be able to sort it from there.

most likely worn out brushes on the motor or faulty motor

To disable the child lock (control panel lock) on the Electrolux EFDE210TIW, press and hold the Dry Time and Wrinkle Release key pad buttons until the indicator light goes off. These are the two buttons to the right of the LCD screen. You will need to hold the buttons for several seconds (usually between 3 and 10 seconds depending on when the dryer was manufactured). See page 11 in the user manual. The manual is available on the product page: https://www.electroluxappliances.com/Washers-Dryers/Washing-Machines/Dryers/EFDE210TIW/ . The direct link to the English version of the manual is currently http://manuals.electroluxappliances.com/prodinfo_pdf/Webster/136936001en.pdf . I hope this helps. Cindy Wells

indicates no water flow from taps or the water solenoid is faulty and not opening the valve

The door of the washing machine cannot be opened here.3. Perform emergency door opening On some machines the door can be opened in an emergency by pulling down on a bar using a screwdriver or similar object, for example. If the machine has an emergency release, it is located next to the fluff filter. See the full description in the user manual. Note: Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain.

Warning: Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down.

Warning: Risk of injury! Make sure that the drum is not rotating. If necessary, wait until the drum stops rotating.

4. Reset the machine Switch off the power to the machine and then switch it on again after about 20-30 seconds. Then test whether the machine is working normally. 5. Contact an Authorized Service Centre If the door cannot be opened without water in the machine and the above advices do not resolve the problem, we recommend requesting a visit by a service engineer.

NOTE: Depending on the problem, you may be charged for a service visit by an engineer, even during the warranty period.

Warning: We do not recommend using the product until the problem has been completely fixed. Unplug the product and do not plug it in again until you are certain that it is OK to do so

6.1 Child lock function This option prevents children to play with the appliance while a programme operates. The programme knob and the touchpads are locked. Only the on/off button is unlocked. Activating the child lock option 1. Press the on/off button to activate the appliance. 2. Press and hold touchpads (A) and (D) at the same time until the child lock indicator comes on. • It is possible to deactivate the child lock option while a programme operates. Press and hold the same touchpads until the child lock indicator goes off. Dado

Hello? Try ManualsLib Makes it easy to find manuals online

which light is flashing & what colour it is e.g (Start, End, door open, etc.)