Electrolux Recent Questions, Troubleshooting Help & Support

1K Products
44K Answers
957K Views

How do we dry or clothes ? We set the program 40° cotton anf 30° it takes too much time waiting for the end program.thus we just manually set the program into rinse then drain.but we got our clothes still wet. Were using electrolux ewf851v.thanks for the answer

try a different number then or hang them on a line outdoors and lt the sun and wind dry them .

Electrolux... | Answered on Mar 26, 2020

My electrolux dryer a couple months back gave me error code 64. I researched and replaced the heater coil along with the two parts attached to it. The limiter and thermostat if I remember correctly. That part failed and I got error code 65 after only two weeks. When I removed the coil it had obviously gotten to hot and the coils warped and touched the side walls. I Replaced again and now I’m getting the same code. What could be causing it to fail over and over?

Model number?

E65 High limit thermostat tripped open too many times (Electric dryer)

So... does the dryer seem to be getting hotter than normal? Try running with "air only" no heat, if it heats then likely the heater relay contacts have welded closed. This condition can damage the element so check carefully.

The relay is likely on the control board $$$ and not sold individually by manufacturer but can be purchased from other component suppliers, eg. Digikey... so long as PCB is not damaged it can be replaced using a 1000W plus soldering iron.

If not overheating then the high limit may be suspect. It is usually located on the exhaust side (blower).

Electrolux... | Answered on Mar 24, 2020

2 Answers

Error message on my electrolux INDUCTION STOVE TOP

Hello - Typically error code E on Electrolux induction cook top indicates an error with the user interface board/control board. Contact a professional to move forward accurately and properly diagnose/repair the unit.

Electrolux ICON... | Answered on Mar 21, 2020

1 Answer

The electrolux 1590 power head is not getting power. How do i fix this? The suction is working just no power to the head for light or brush.

Here's a YouTube video describing how to troubleshoot a electrolux 1590 power head. It will cover all possibly faults.

https://youtu.be/mQQ8HKByy3c

Electrolux... | Answered on Mar 19, 2020

1 Answer

My Electrolux dishlex dx303 has stopped heating water. I have resoldered relay with no change. Please help

if voltage to heater element bad element if no voltage bad board

Electrolux... | Answered on Mar 17, 2020

1 Answer

How do i cancel the program on a dx302 when i have started cycle

A program can be cancelled during the wash cycle by pressing the program/clear button for 3 seconds.
Note: the wash cycle must be running to cancel the program.

Electrolux... | Answered on Mar 16, 2020

3 Answers

Electrolux power nozzle N106M does

This is a pretty common problem , and it's usually caused by 1 of two things. Both are pretty simple fixes. try the reset button which is located by the L shaped part on ur powerhead. try pushing that while ur machine is turned on for the carpet areaThe first thing you should try is simply eliminating the wand assemblies from the vacuum cleaner. So remove the hose from the upper wand, and disconnect the lower wand from the power nozzle. Now try connecting the hose directly into the power nozzle and turn on the vacuum cleaner, and power nozzle. Does it work? If yes, then one of your wands has gone bad, and you'll need to replace it. If the power nozzle still won't come on, then you may have a much simplier problem. on the neck of the power nozzle. You will see a small circle indent on the front part of the neck located underneath of where the wand connects into the neck. This is actually a cover that hides a screw below. Simply use a small flat head screw driver, and pop off the small circular cap that hides the screw. There is a Star bit screw underneath. I believe it's a T15, but it may be a T10 sized screw. Use I believe a T15 Torx screw driver and remove the screw from the neck.

Once the screw has been removed, Use a flathead screw driver, and pry the front cover of the neck off. It shouldn't take a lot of force, and should come off pretty easily. Once this has been removed, you should see to metal pins, and two lead wires. What happens is the lead wire becomes disconnected from the metal pin, which then prevents the power nozzle from turning on. Simply reattach the lead wire into the metal pin, and snap the front cover of the neck back on. Put your screw back in, and your screw cover (or you can just leave this part off, you'll probably be having to remove it frequently to reinstall the lead wire, lol).

If neither of these two problems fixed your machine, then it sounds like you may have a bad hose assembly. Hopefully this isn't the case, and it's usually not. 9 times out of 10, it's just the lead wire that's come loose.

Electrolux... | Answered on Mar 09, 2020

3 Answers

Ew1045f washing machine purchased in india.

try checking the carbon brushes.

Electrolux... | Answered on Mar 04, 2020

11 Answers

Electrolux Icon Oven won't self clean - "Remove Racks" displayed

I was getting the remove rack error until I finally figured out what it wanted me to remove. When you say you removed the rack supports, do you mean just the sliding parts or the whole side metal rack support? At first I thought they were bolted in, but I read somewhere that they come out, too. Upon further investigation, I found the rack supports just slide into the side walls at 4 points. I had to use a little force to pull them out, but they came out and my oven is self-cleaning as I write this. I just thought I would share in case you or others haven't figured it out yet. Now I will just have to see how hard it is to get them back in...

Electrolux ICON ... | Answered on Mar 03, 2020

2 Answers

Pump motor runs continuously, ''Eco'' flashes continuously

Hi
soyunds like it flooded the base
You need to dry out the base of the machine thoroughly and it should re set

Electrolux 24... | Answered on Mar 01, 2020

1 Answer

Electrolux washing machine W3600X showing ERROR INTERLOCK please help me to solve this issue

Broken actuator on lid?

Electrolux... | Answered on Feb 29, 2020

2 Answers

I have Electrolux EDH3897SDE dryer, and I can not disable child lock. Do you have any suggestions?

Press and hold the power on/start button.

Electrolux... | Answered on Feb 24, 2020

1 Answer

How do I turn off demo mode in Electrolux wall oven EVE623SA?

I used https://www.google.com to search for a manual for the EVE623SA.
https://www.manualslib.com/manual/749580/Electrolux-Eve611sa.html?page=20#manual
Page 20 of the manual gives the following instructions. Please comment to let us all know if it works for you.

1. Ensure the oven is in the off state. Press and hold the + button until a beep sounds. The 'Demo' text will begin to flash.
2. While holding the + button turn the function selector to the first oven function until another beep is heard.
3. Then turn the function selector to the 'off' position.
4. Release the + button.
5 Toggle and hold the temperature selector to the right (+) until 3 beeps sound.

Electrolux... | Answered on Feb 12, 2020

1 Answer

I have an Electrolux Oven EVEP6155A. I have a fault Code F239 showing on the screen Can you please help

this is a error for the touch controls its normally caused by moisture getting on it, theres an upgraded part you can order from electrolux which is basically just a strip of foam you fit under the touch controls to prevent moisture getting in

Electrolux Ovens | Answered on Feb 07, 2020

0 Answers

Resetting filter indicator on Electrolux oxygen air purifier

Electrolux Air... | Posted on Feb 01, 2020 | Be the first to answer

2 Answers

My electrolux ewf14012 washing machine stops with 45mins to go saying check taps. We've cleaned the filter & checked the taps & all seem to be working fine. Any ideas on how to fix it?

"Check the tap" means difficulty with inlet water.
Before anything I suggest to clean the water inlet filters as described in the user manual.

cleaning inlet valve filter-kjr1zbbqwoqdv4an3hks3bv2-1-0.jpg

cleaning inlet valve filter-kjr1zbbqwoqdv4an3hks3bv2-1-0.jpg

otherwise could be:
Tap closed or water pressure too low; drain pipe improperly
positioned; water fill solenoid valve faulty; leaks from water circuit on
pressure switch; pressure switch faulty; wiring faulty; main PCB
faulty.

Dado

Electrolux... | Answered on Jan 30, 2020

0 Answers