Have a 1993 accord only key i have is ign. what does key for back seat release and shift lock and gas lock look like ?

Question edited for clarity.
Question moved from Television and Video category.

Normally you remove the back seat back, and pull the emergency release. Or a mobile locksmith can get in. If the lock is worn, any similar shape key may work with some jiggling. Also look in the glove box for a release button.

I just found this in your Owner Manual for Cutlass Supreme

Remote Trunk Release (OPTION) Press the yellow trunk release button located under the instrument panel on the driver's side. Your automatic transaxle must be in P (Park). Remember that your trunk can be opened at any time using the lock release. Be sure to lock your doors

and also access into the back.

Trunk Access Panel If you have split rear seats, you may have a trunk access panel for storing long objects like skis. Pull your rear armrest down using the strap. Then pull the latch on the trunk access panel towards you to open the panel. To close the access panel lift the latch.

https://carmanuals2.com/get/oldsmobile-cutlass-supreme-1993-owner-s-manual-79185

Videos regarding a locked trunk.

https://www.google.com/search?q=open+the+trunk+on+93+oldsmobile+cutlass+ciera+without+key

..

The seats don't fold down but you may be able to pull the upright part of hte back seat out enough to fish a pole in and grab the keys. Otherwise locksmith($60 or so usually). In my experience the dealer will cost a few hundred for a new key. For a 26 year old car, Id even break the trunk lock with a flat head screwdriver.

Ign Systems 8D - 19 Service manual '92 Dak
Disconnect neg battery cable Tilt column:Remove tilt lever (counterclockwise) Remove upper and lower covers (3 screws) Remove ign switch mounting screws (3) with torx bit Gently pull switch away from column Release two connector locks on the seven-terminal wiring connector. Remove connector from ign switch Release connector lock on the Key-in-switch and Halo Light four terminal connector. Remove connector from switch Remove key cylinder from switch as follows: With key inserted and ign switch in the LOCK position use small screwdriver to depress the key cylinder retaining pin flush w/ key cylinder surface Rotate the key clockwise to the OFF position The key cylinder should now be unseated from the ign switch assembly With key cylinder in unseated position (key cylinder bezel about 1/8 inch above ign switch halo light ring) Rotate key counterclockwise to LOCK position and remove key Remove key cylinder INSTALLATION; Install electrical connectors to switch making sure locking tabs are fully seated into connector Mount ign switch to column Shifter must be in PARK position Park-lock dowel pin on ign assy must engage with park-lock slider linkageVerify ign switch is in lock position (flag is parallel w/ ign switch terminals..off to the right) Apply dab of grease to flag and pin Position park-lock link and slider to mid-travel Position ign switch against lock housing face Be sure pin is inserted into park-lock link contour slot Tighten screws Assemble cover Tighten more screws Tilt column and install tilt lever (clockwise) instsall neg battery cable Gently insert key cylinder into ign switch asssy until it bottoms Insert key and gently push key (inward) and rotate clockwise to end of travel Rejoice in how much money you just saved yourself

Use your ignition key and stick it straight down into the slot marked shift lock, next to the shifter. That will allow you to shift it into neutral. Leave it there, remove the key from that slot and start the car. You will then be able to shift into drive, from neutral, and be on your way.

pull rear seat base -------push back hard and lift to unclip
then unbolt seat back and lift up ther should be holes in metal
spot your keys and fish them out

It locks the lever that opens the trunk of the car so you wont be able to use that lever to open the trunk from inside the vehicle. The master key should fit in it. You will still be able to open the truck with the key on the outside right at the trunk with the key even if you have the lever locked. It's a security thing. I hope this helps.

My 1993 honda accord is locked in park, and i have no break lights,how do i fix this.

Do your brake lights work?

I have a 1993 honda accord and my clock won't keep time,can you help

My daughter drives a Suzuki, my solution to her is: while the gear shift lever is in park, lightly put pressure on the gear shift lever, through the park position and while pressing the gear shift towards park light rock left to right while trying to remove the key.

The interlock between the transmission and the ignition switch needs to be adjusted/ repaired or replaced.