Put new batteries in the remotes and the four lights blink twice when you push power

If you have an RCA 26211 remote, you can program it to control a DVD player by following these steps:

1. Press and hold the "Setup" button on the remote until the red light on the remote blinks twice.

2. Enter the code "9-9-1" on the remote. The red light will blink twice.

3. Press and hold the "DVD" button on the remote. The red light will blink twice.

4. Enter the code for your DVD player on the remote. The code will be four digits long.

5. Press the "Power" button on the remote. The DVD player should turn on.

You can find the code for your DVD player in the manual that came with the player, or you can look it up online.

make sure your tv is on.. On the remote control, press TV once.
. Press and hold set until the l.e.d. red light blinks twice,
then release set.. Enter the first four-digit code for your tv
the l.e.d. will blink twice. If the l.e.d. did not blink twice, repeat steps 2 through to 4 and enter the code again.
.point the remote control at the tv and press power once.your tv should turn off. If it does not, repeat steps 2 through to 5...i think these codes might work for you set .0236, 0463.

You may have a lockout problem. push on power button then push the horn twice to reset the lock. Strege Mobility

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

The codes are....0650,0226,0108,1650,0037,0367,0516,0361,0056,0548,0853,0163..PROGRAM..Turn the TV on, press the TV button on the remote, press and hold the MAGIC button until the LED blinks, the light will blink once then twice, enter one of the four digit codes, the light will blink twice, press the power button,the TV should turn off, if not, repeat the steps using a different code until it does....hope this was helpful....

The codes are,0503,0695,1045,...turn the DVD on,on the remote, press and hold the set button until the light blinks twice,then release set button,then enter one of the four digit codes, the light will blink twice,if not try another code,then press power button, it should turn off......hope this was helpful....

The codes are, 0037,0218, Have fresh batteries,press TV button, press and hold down the MAGIC button,red light blinks twice, enter one of the four digit codes, press POWER.....hope this was helpful...

The Sky+ remote should automatically default to Sony TV's. Leave the batteries out for a few minutes and try again. The Code for Sony is 0000.
Or try this :-

With TV and sky box on.
Press the 'TV' button on the remote.
Hold down the 'select' and the 'red' button (of the four coloured buttons) together, until the red light on the remote blinks twice. (takes 2 seconds)
Press the 'TV' button again.
Now enter four zeros, the red light on the remote should blink twice.
Press the 'standby' button (top right).
If the TV turns off, then press 'select' and the light should blink twice again, job done.

If the TV does not turn off then press 'TV' followed by 'standby' again.
Alternate pressing 'TV' 'Standby' until the TV turns off.
When it does, finish by pressing 'Select.
Check the red light on the remote, if it blinks 3 times, then it has run out of options for 0000.

These are the steps to program your URC 3021 remote:

To setup your URC-3021 for a TV, these are the steps:

1. Turn on your TV.
2. On the remote control, press TV once.
3. Press and hold SET until the LED (red light) blinks twice,
then release SET.
4. Enter the first four-digit code for your device. If performed correctly,
the LED will blink twice. If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.
5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 through 5, trying each code until you find one that works.

I have the same problem for my dell note book
This is how i solve it

Unplug your note book from any power source
then remove the battery from the Notebook for
30 minutes after 30 minutes put back the battery and reconnect your adapter to power source turn on the power