Tint is too pink or red on all the channels. Under controls menu I adjust the tint to green but the problem stays.Is this a setting under adjust or setup or is the tv tube gone? I don't have the original remote to get to the adjust or setup area in the menu. thanks

Sounds like a bad LCD panel.Sorry for the bad news

Color balance is labeled "Tint"
Color amount is labeled "Color"

Both are in the "picture" adjustments menu.

Either your tint is swung too far to red, or the color setting is wide open making normally pink faces look sunburned...likely it's a combination of the two; Too much red, and a bit too much color.

Going back to the "default factory setting" in "setup" will also drop all settings to center.

you need to tacke it back to the shop

My 43fdx20b had a pink tint to it also. The picture was clear otherwise. I found, on mine, I needed to adjust the Red Screen control. It was located behind the front panel. I removed the two screws on either side of the front panel and was able to remove the panel. Then I adjusted the Red Screen control. I found that if I tuned in an old Black and white movie I could adjust the color fairly accurately. Good Luck.

Go to menue on controller, then Picture, then adjust Color and Tint to you taste. The color ajusts Blue and Green move left more blue move the slider right more green. The Tint controlls red. More red move right less left. Also chech Color temp setting.

Here is something that may help from the toshiba.com website under your model number television. Q. Why are people on my screen green?
Models: 32HL17, 37HL17, 42HL17, 42HL167, 47HL167, 52HL167, 42HL167, 42LX177, 46LX177, 52LX177, 57LX177
REF:FAQLCD00107
If the problem is not the connections, try adjusting the tint on your television. A high tint setting will usually create a green
image on the screen where as a low tint will create a more red hue. In order to access your television's tint:
1. Press the “MENU” button on your remote control and use the LEFT or RIGHT arrow keys and select the
VIDEO menu.
2. Then use the UP and DOWN arrow keys to highlight PICTURE SETTINGS and press the "ENTER" button on
your remote.
3. Next use the UP and DOWN arrow keys to highlight TINT then use the LEFT or RIGHT arrow keys to adjust the
TINT. If the picture is too green the tint will need to be lowered.
4. Once you have adjusted the tint to your liking, use the DOWN arrow key to highlight DONE and press ENTER. The toshiba customer service telephone number is : 1-800-631-3811. I hope this helps you with your problem.

Picture Menu
Picture Mode: Expert1
*Backlight: 16
*Contrast: 83
*Brightness: 53
Sharpness: 50
*Color: 55
*Tint: 0
Expert Control

• Fresh Contrast: Off
• Noise Reduction: Medium
• Gamma: Medium
• Black Level: Low
• Real Cinema: On
• TruMotion: Low
• Color Standard: HD (N/A w/HDMI)
• White Balance: Warm
• **Method: 10-Point IRE
  • 10 IRE
    • **Red: 1
    • **Green: 2
    • **Blue: -16
  • 20 IRE
    • **Red: -6
    • **Green: 0
    • **Blue: -7
  • 30 IRE
    • **Red: -5
    • **Green: 0
    • **Blue: -4
  • 40 IRE
    • **Red: -8
    • **Green: 0
    • **Blue: -4
  • 50 IRE
    • **Red: -4
    • **Green: 4
    • **Blue: -4
  • 60 IRE
    • **Red: -6
    • **Green: 6
    • **Blue: -5
  • 70 IRE
    • **Red: -8
    • **Green: 3
    • **Blue: -10
  • 80 IRE
    • **Red: -8
    • **Green: 7
    • **Blue: -16
  • 90 IRE
    • **Red: -9
    • **Green: 5
    • **Blue: -18
  • 100 IRE
    • **Red: -10
    • **Green: 4
    • **Blue: -9

Color Management System

• Red Color: 0
• Red Tint: 0
• Green Color: 0
• Green Tint: -15
• Blue Color: 0
• Blue Tint: 11
• Yellow Color: 15
• Yellow Tint: 2
• Cyan Color: -15
• Cyan Tint: 0
• Magenta Color: 0
• Magenta Tint: -1

lg70 nice tv excellent processor just to bad there is no intensity control on color management oh well still better than what the three s are pushing block out the hype lg will be number 1 in a few years haters are starting to come around and well leds coming,

p.s. i dont work for lg just tired of losers bashing stuff because they dont own it.
im isf certified those settings are right on the money straighter than a ruler

Colorimetre HCFR software
AVC HD 709 calibration disk
Spyder2 colorimeter (I know most prefer the Eye-One meters, but the Spyder2 was available from my job at no cost)

Here are the settings:

PS3 Blu-Ray player

Output Format (HDMI): Y Pb/Cb Pr/Cr (important!!! NOT RGB output)
BD 1080p 24hz Output (HDMI): On (this TV can reproduce video at 48hz for accurate 2:2 pulldown)
Y Pb/Cb Pr/Cr Super White (HDMI): On (not sure if this matters)

42LG50 Settings

Aspect Ratio: Set By Program (Personal Preference)
Picture Mode: Expert 1
Backlight: 50 (Personal Preference)
Contrast: 54
Brightness: 54
Sharpness: 40 (Personal Preference)
Color: 50
Tint: 0

Fresh Contrast: Off
Noise Reduction: Off
Gamma: Medium
Black Level: Low
Real Cinema: On

White Balance: Warm
Method: 10 Point IRE

10 (-3,8,-16)
20 (15,24,-21)
30 (20,36,-22)
40 (3,19,-40)
50 (8,34,-41)
60 (10,50,-20)
70 (-5,50,-8)
80 (-16,50,18
90 (-14,50,30)
100 (-22,38,21)

Red Color: -3
Red Tint: 0
Green Color: 10
Green Tint: 0
Blue Color: 14
Blue Tint: 0
Yellow Color: 0
Yellow Tint: 1
Cyan Color: -11
Cyan Tint: 0
Magenta Color: 0
Magenta Tint: -2

Take time to get used to the settings, you may think the screen looks dull at first. The truth is most people have way too much contrast on their TVs.
These settings will also work for Cable or Dish hookups, in which case you may change the Noise Reduction option to Medium to reduce signal noise.

OR....

2POINT IRE

Backlight: 65
Contrast: 55
Brightness: 45
Sharpness: 50
Color: 45
Tint: 0

Fresh Contrast: Off
Noise Reduction: Off
Gamma: Medium
Black Level: Low
Real Cinema: On

White Balance: Warm
Method: 2 Point

Red Color: 3
Red Tint: 0
Green Color: 9
Green Tint: 2
Blue Color: -1
Blue Tint: 0
Yellow Color: 6
Yellow Tint: 5
Cyan Color: -1
Cyan Tint: 1
Magenta Color: 2
Magenta Tint: -1

Hopefully someone on here has a manual and can tell you exactly where the tint controls are. Also need to try adjusting the color level, turn it clear down so you have a black and white picture.
Is the picture still green over the screen with the color control
set clear down to black and white? If it does, you might
have an issue with the green gun going out or problem in the
circuitry to it.


By the way, the best way to adjust the picture settings on a
tv are to first turn the color control clear down, then adjust
brightness and contrast for best black and white picture, then
bring up the color level to where it should be and adjust the
tint for best red/green ratio.

The monitor is broken. The circuits that generate green in the RGB setup are not working. If its under warranty, replace it.