My husband is too proud to ask this silly question. But where/which one is the inlet valve and outlet valve on a bobcat 743b

https://skidsteerloadermanual.com/store/products/bobcat-743b-loader-service-manual-download/

If he has takin the fill hoses off the unit and tested them for flow and the filters on the water valve are clean, then yes the fill valve would need changed.

what are you asking?
do you want to know how to plumb the individual pieces of equipment?
If so, skimmer port at the pool will go into the suction port of the pump, the port directly into the hair & lint pot.
discharge off the top of the pump will go into the Inlet of the filter valve, then the outlet of the filter will go to either a heater inlet port then outlet of the heater to the pool return inlet ports. If no heater, then from filter outlet directly to the pool return inlet fitting.

Good luck

from the belt side first valve is inlet second valve is exhaust..bigger valve is inlet small valve is exhaust also you will have a black colour in exhaust valve stems...

Guessing the water system is turned on and all velve open. There is an electic water inlet valve on the dishwasher, thet maybe clogged from sand in your water supply. The valve is located where the water enters the dishwasher on the buttom, the valve has a strainer filter that gets clogged sometimes. (if your not on a city water system this is a common problem) You will need to turn the power off to the dishwasher, and remove the inlet valve assembly(blue in color some machines) when you get the valve assembly out remove the inlet, and outlet hoses form it, check the inlet orafose for sand etc, and clean this in warm soapy water, even let it soak in a pan for a while. re assemble in reverse order, see if you get water into the dishwasher when you get it re-assembled and powered up.

My water heater has three water connections on the top of it one has a C for cold is that a inlet or outlet ? IT'S THE COLD INLET. The other spot has a H for hot is that a inlet or outlet ? IT'S THE HOT OUTLET. And the other one is not marked what is that one for and is it a inlet or outlet ? please email me at [email protected]. The last one is a pressure release valve that lets off excessive pressure when the temperature goes too high in the unit. When you install the heater, it should be installed into the drain pan that existed before or into a new one. You should also install a drain pipe from the valve to that drain pan, or into the drainage system for the house. This may depend on the codes where you live. Also install a good quality shut off valve on the inlet side for emergencies. A Ball type is good. Hope this helps,
Best Mark
I'm new to this site, so I'm not sure if I can email you directly or not. I believe not. Good Luck.

you might to get new batteries the might have been charged and discharged to many time

HI. this will occur if the inlet valve assembly is experiencing issues, within the solenoid structure. In some cases, debris will build up, in return, not allowing the solenoid to completely close, when not in use(the solenoid can also fail as well). This will cause a slow drip, or a leaky dispenser spout.

The water inlet valve is located behind your refrigerator. Find the water supply line coming into the valve and turn it off at the source (typically under the sink). Disconnect the supply line. Remove the screws that secure the inlet valve in place.

The water inlet valve is connected by two wires. Label the wire placement on the water inlet valve before disconnecting the wires. The wires are connected to the terminals with slip on connectors

Firmly pull the connectors off of the terminals (do not pull on the wire). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If the connectors are corroded they should be replaced.

Inspect the filter screen where the supply line connects. Remove any debris or deposits that may have built up using a toothbrush or warm running water. If you cannot clear the clog, it will be necessary to replace the valve (the filter is not removable on most inlet valves).


Test the water inlet valve for continuity using a multimeter. Set the multimeter to the ohms setting X100 (if available, otherwise use the nearest ohm setting). Place a probe on each terminal. The multimeter should display a reading of 200 to 500 ohms. Close inspection of the inlet valve and especially the coil may reveal the exact ohm resistance rating to test for. If the water inlet valve does not pass this test, it should be replaced.

Hoshizaki machines have a water inlet valve that can stick in the open position. This will cause the machine to do silly things. If you can turn the machine off and you can still hear water running, the valve is stuck open. It is an easy fix. Water valve only has 2 wires going to it and 2 water lines. One inlet and one outlet. Just turn off water and kill power at the breaker before doing any work.

Hope this helps and good luck.

Try Rick and Restaurant Parts and More in Ohio for a replacement valve. 1-888-814-1110

Have you ask your handsome man?