Top 20
Ariston Technologies AW129NA 16 Lbs Front Load Washer - Page 3 Questions & Answers
Why is h20 sign popping up
The washing machine fails to load water (The wording H20 is displayed).
- The water inlet hose is not connected to the tap.
- The hose is bent.
- The water tap is not turned on.
- There is a water shortage.
- The water pressure is insufficient.
- The START/RESET button has not been pressed.
Dado
7/18/2014 9:34:49 PM •
Ariston...
•
202 views • 0 helpful votes
F13 ERROR
F13. NTC (Dryer Temp) Open / Short
Check wiring continuity to Control Board.
Replace NTC.
Or, replace Control Board
NTC is the temperature sensor
6/22/2014 4:48:21 PM •
Ariston...
•
401 views • 0 helpful votes
Washing machine manuals
You'll find these on line, just type the model number into google.Make sure to use the manufacturer's site, not a proxy.
7/23/2014 9:36:00 AM •
Ariston...
•
150 views • 0 helpful votes
Avtxf 149 f-08
F08 - Heater relay cannot be activated
- Check wiring
- Check pressure switch and connections
- Tap relays as they can jam on new boards
- Check electronic control PCB
- Check heating element
Dado
6/21/2014 6:40:38 AM •
Ariston...
•
115 views • 0 helpful votes
How to remove front of Ariston washing machine AVD 129 SK
take the top off,remove the soap bucket,take the screws off on the pc board/front cover. the top screws of the front pannel are usualy behind the display cover. the botom screws are behind the bottom plastic cover which you have to prey off with a screwdriver from the top side.
3/18/2014 12:47:19 PM •
Ariston...
•
616 views • 0 helpful votes
Ariston washer/dryer arwdf129na
F04: Overflow and Pressure Switch Empty found at the same time (Pressure Switch stuck on Empty)
Overhaul CN1
Overhaul Pressure Switch Contacts
Control CN1/Pressure Switch Continuity
Replace Pressure Switch
Replace Card
Dado
4/23/2014 2:04:05 AM •
Ariston...
•
125 views • 0 helpful votes
I have a code H 20 then it goes to F01
The washing machine fails to load water (The wording H20 is
displayed).
• The water inlet hose is not connected to the tap.
• The hose is bent.
• The water tap is not turned on.
• There is a water shortage.
• The water pressure is insufficient.
• The START/RESET button has not been pressed.
F01: Triac Short circuit
Overhaul CNE
Replace Card
Dado
4/5/2014 1:48:50 PM •
Ariston...
•
112 views • 0 helpful votes
Axvf120rr f10 error
F10: Pressure Switch Empty and Full or neither Empty nor Full
Pressure Switch Found
Overhaul CN1
Overhaul Pressure Switch Wiring
Control CN1/Pressure Switch Continuity
Replace Pressure Switch
Replace Card
Dado
1/30/2014 7:31:23 PM •
Ariston...
•
210 views • 0 helpful votes
Ariston ARF 105 H2O error!
I had this issue also and it was because I started the machine and had not turned on the water to it. However, it cleared when I unplugged the power cord, waited about ten seconds, then plugged it back in. I guess they need a "reboot" once in awhile, like a computer - at least mine did. Hope this works for you, too.
11/5/2013 6:24:07 AM •
Ariston...
•
1,999 views • 0 helpful votes
Al1080 reset ariston
It is
possible that the machine does not start off the cycle because there are errors
due to feedback from the inputs. For the program to start up the main program
controller must initiate the INLET/MOTOR/DRAIN
pump/ valve to open up and allow each function to be driven starting from
the flow of water into the drum as also the drain valve to open to exit the
water at the point of the program cycle. If this does not happen then the
voltage at the valve/motor/pump must be checked or the fault relates to no
voltage from the controller. This means
the controller is a suspect.
1/17/2013 10:08:24 PM •
Ariston...
•
176 views • 1 helpful votes
Ariston AQXXF 129 Error code F 05 - What is this?
see this causes and fix it. God bless youF05
Water temperature sensor error
If during the water heating step in the wash cycle, the water temperature
sensor (NTC) value is out of range, or the heating element circuit has
failed, the F05 error code will be displayed.
Potential Causes
• Check the Water Temperature Sensor, Heating Element and Element Relay
• Check connections to the Sensor, Heating Element and Relay
Replace failed component.
9/30/2012 10:23:56 AM •
Ariston...
•
2,741 views • 0 helpful votes
Not finding what you are looking for?