20 Most Recent Ariston Technologies Ariston AWD12 Front Load Washer/Dryer Questions & Answers

F06: Selector Error
Overhaul CND (selector connector)
Overhaul Selector Connector
Control Selector/CND Continuity
Control Selector Motor
Replace Selector
Replace Card


Ariston... | Answered on Jan 06, 2019

check belt if ok see if pump is working

Ariston... | Answered on Jun 15, 2018

Reading the error code

The fault on the appliance is signalled via:

1. the continuous rotation of the selector knob
2. the action, for the first 4', of the electrovalve and the drain pump
3. the door becomes unlocked
4. the led flashes: the number of flashes indicates the fault code; the code should be read as follows:
· each fast flash (2/3 flashes of the led very close together) represents one code value
· the fault code is evaluated by counting the number of flashes occurring at 3/4" intervals from one another
· stop counting when the washing machine waits the equivalent of approximately 8/9" between flashes
· the procedure is repeated by the appliance cyclically

After you determine which the alarm code appeared we will able specifically to help you.


Ariston... | Answered on Mar 01, 2018

Maybe get a knob type & eliminate this type of problems

Ariston... | Answered on Nov 22, 2017

Sounds like the washer control panel has failed.

Ariston... | Answered on Jul 14, 2017

Lamp M flashes slowly when the appliance is switched on and
a waiting instructions and at the end of a cycle, indicating that the door can be opened. It flashes quickly when the door should not be opened. A steady light means the appliance has accepted the selected programme.

24967037-ineink0kisfnom0atbkujjcx-3-1.jpg If you correctly use the appliance then defective can be interlock, wiring or board.
If the door is constantly locked then you can access to interlock by removing the top cover of washing machine.


Ariston... | Answered on Oct 28, 2015

F09: Machine Setup Error Found (AWD12)

Setup error or incompatible EEPROM
Control Microprocessor Version
Ask for EEPROM Spare Part indicating Microprocessor version
Reflash EEPROM
Check electronic controller


Ariston... | Answered on Oct 11, 2015

Sounds like a faulty solenoid valve. Does the water over flow the door and run out onto the floor? The other possibility is that the electronics could be faulty energizing the coil when the machine is off but this is not likely. Do you turn the valves off at the source when you are not using the machine? This would be a simple fix versus going into the machine to find out if the coil is energized or to replace the solenoid valve.

Ariston... | Answered on Dec 04, 2014

If the drum is not turning, the motor control board is faulty. This may just be a bad solder joint, but you'll need someone with electronics knowledge to check and repair it.

Ariston... | Answered on Sep 14, 2014

You will have remove top cover, and release door latch from inside the front, with a screw driver pushing against the latch to open door.
It does mean that you probably have a faulty door lock, or broken door handle.
Please rate my fixya solution.

Ariston... | Answered on Aug 30, 2014

If there are no lights, check the fuse in the plug.

If the machine comes on but the drum does not move, the motor control circuit board probably has a burnt connection or bad joint. This may also be the cause of the fuse blowing.

Ariston... | Answered on Jun 06, 2014

Not finding what you are looking for?
Ariston Technologies Ariston AWD12 Front Load Washer/Dryer Logo

196 questions posted

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts


Level 3 Expert

85239 Answers

Eric Taylor

Level 3 Expert

590 Answers


Level 3 Expert

6740 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ariston Technologies Washing Machines

  • Ariston Technologies Washing Machines

Most Popular Question

machine swallow conditioner leaves some

  • Washing Machines