Ariston Technologies AW129NA 16 Lbs Front Load Washer - Answered Questions & Fixed issues


This video will show you how to keep your soap draw clear and how to service the parts
Please remember to subscribe to our YouTube channel for all appliance tutorials
a 4 THUMBS rating is appreciated for answering your FREE question.

Ariston... | Answered on Jul 30, 2013 | 204 views


it is poss that you pressure system has not released, and this can keep the door closed. Unplugging it will not cure this fault. It is also poss that you have a blocked filter or waste. Unfortunatly has you are older people I would call an engineer

Ariston... | Answered on May 30, 2012 | 7,350 views


Many times faults like this can be cured by Uplugging the washer from the mains power supply and leaving for 10mins. Also check all filters, drain and supply lines are clear and not kinked.

Ariston... | Answered on May 04, 2011 | 786 views


SOUNDS LIKE THE HEATING ELEMENT HAS GONE

Ariston... | Answered on Jan 09, 2010 | 260 views


hi,
The cycle doesn't advance
When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. 


It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

Thanks for your question.

Ariston... | Answered on Jan 20, 2009 | 531 views


Dear babmat: just now got your question. We are very satisfied with our ARISTON Washing Machine. I trust that that is what you are inquired about? I had the same problem the first time. This locking occurs when one opens or tries to open the washing machine door too soon!!!! It has to be left alone for a few minutes. When I waited and later tried again to open the machine, I did not have a problem.
Just wanted to leave this note for anyone who encountered the same problem. You, yourself, hopefully, might have gotten that answer and the problem fixed in the meantime!?
Greetings, handinovice

Ariston... | Answered on Nov 01, 2008 | 907 views


try pause/cancel twice to open door open detergent disp look for a plastic string and pull it

Ariston... | Answered on Dec 31, 2007 | 168 views


Pump fault or more likely blocked filter try cleaning should reset it self

Ariston... | Answered on May 06, 2019 | 4,238 views


did you check breaker in breaker panel

Ariston... | Answered on Jan 05, 2019 | 57 views


https://www.needapplianceparts.com/aristonerrorcodes.aspx.

Ariston... | Answered on Dec 16, 2018 | 235 views


Has anyone got manual for ariston K-LB 121?

Ariston... | Answered on May 02, 2018 | 103 views


when I wash heavy stuff it will not spin properly because the weight is not distributed evenly over the load and it stops every time. you may need a repair man unless you can just move the dial to a drain spot rather than spin, if enough water gets out it will probably open then.

Ariston... | Answered on Jun 15, 2018 | 109 views


H2O is the symbol for WATER and probably indicates a WATER related fault on your machine. A pressure switch is the normal way the machines 'sense' when the level is sufficient. Overfilling suggests a faulty switch, which will need to be replaced by a technician. Also, ensure that the machine drains as it should, if not, the pump filter may be blocked.

Ariston... | Answered on Apr 04, 2018 | 442 views


Before you change fuses, do you have an internal fuse board or RCD system in your home? Sometimes, an individual RCD can trip out, locking off sockets. Some sockets are individually set up for up and downstairs in a house, or different rooms. If you have a board or RCDs, check them out :)

Ariston... | Answered on Nov 18, 2017 | 79 views


This is normal , it takes small quantity of water unlikes old washing machines

Ariston... | Answered on Oct 04, 2017 | 57 views


Washer fills with water and overflows:

The water pressure level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. To determine if the switch is bad, you should first eliminate the air dome hose as a problem. Look for signs of cracks or worn areas on the hose. Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. If the air dome hose appears to be ok, then the water level switch may be defective.

You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube.
If the machine starts to wash. the pressure switch is more than likely good
( No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED).

The other item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test.
Also another trick to check the water valve, is to first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed

By the way my advice is free cuz God is good!




Ariston... | Answered on Dec 08, 2016 | 39 views


I am supposing you are wanting a drive belt for your machine. Please type in "Ariston" on your search engine, as I did, and you will find that you can call them for your answers to your problems.
After a little looking, I found them in about 4 minutes.
God bless your efforts.

Ariston... | Answered on Jan 05, 2016 | 45 views


F18 - Communication error

Ariston... | Answered on Dec 21, 2015 | 731 views


You did not specify model!

F08 - Heater relay cannot be activated
  • Check wiring
  • Check pressure switch and connections
  • Tap relays as they can jam on new boards
  • Check electronic control PCB
  • Check heating element

Dado

Ariston... | Answered on Dec 21, 2015 | 1,310 views


F02 - Motor tripped, tachogenerator open circuit or short circuit.

24960779-ineink0kisfnom0atbkujjcx-3-1.jpg

Dado

Ariston... | Answered on Oct 28, 2015 | 193 views

Not finding what you are looking for?
Ariston Technologies AW129NA 16 Lbs Front Load Washer Logo

23 questions posted

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Harrie

Level 3 Expert

6746 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...