Sunbeam 2370 MixMaster Series Stand Mixer - Answered Questions & Fixed issues

To disassemble a sunbeam mixmaster 2370, find four plastic snappers arranged at 1, 5, 7 and 11 o'clock around the front circle of vents. They can be seen with the help of a good flashlight. un-snap them and the top and bottom shells will separate. From there on, it is clips and screws. Good luck!

I have a 1977 Sunbeam Mixmaster Catalog No. 1-150, service No. 1-15H. Where can I find parts & a manual?

Push down slightly on the head and then the button will go in further and the top will release. ((this answer after I just bought it home and was about to take it back to the store!!))

Hi Eschill,
The model you posted was 2370 and mx8900w ar enot the same. YOu may want to check the basic troubleshooting guide based on the model of your mixer. Just click this link MANUAL. Just message me if you have any question.

I left mine in a hot tub for well over an hour. It started reading room temp at about 125 degrees. It worked for me to put the thermometer in the freezer until the readings were correct. hope this works for you.

hello,

what the problem of engages and disengage indicate from your explanation is that there have been a failure of wire that is apower supply problem .

but for the shaft that jump out from it position it can be replace back to it place

carefully unscrew the processor from the screw if any with a screw driver (technician tools) then first of all try to see if you can fine the loose wire i disc oust about if there is non the it then mean that the shaft have gone bad which will need a replacement to get a better one of it and the same size you will have to take the processor to the store that a technician store around you well you can get a good part that will be compatible or at the producer office or branch.

thank you and thanks for using fixya.

I found a copy of the manual here: http://kitchen.manualsonline.com/manuals/mfg/sunbeam/stand_mixer_models_2370_2371_2379.html . This is a bilingual edition meant to be folded in a pamphlet.

I hope this helps

Cindy Wells

Put a few drops of cooking oil in the holes the the beaters are inserted inMake sure to unplug the unit. Pushing the button, work the beaters pulling lightly. Good Luck

Hi Emily,

Thanks for using FixYa.

Sounds like you have a very simple loose capacitor or shorted capacitor problem. You can bring it to any electronic repair shop for a quick repair. Expect a 15-30 minute job for that.

I hope this helps. Thanks and good day.
-HotRatchet

Hello Hdjohnston! If I were you I would call Sunbeam's Customer service number
Or email them and ask for a replacement user's guide (aka manual). This shouldn't be a problem as I've gotten replacement guides for other things before with no trouble :) Better yet, here's a link to get you your manual from Sunbeam's official website:
http://www.sunbeam.com/InstructionManuals.aspx?section=

Also, if you sunbeam mixmaster is like mine, it you look at the holes where the beaters are inserted it shows little symbols of beaters (one with for example a square top and the other with a more curved top) which lets you know which type of beaters goes in where!
Hope this helps! Kat

Hi, GLENNHOLD148 - With a motor that runs and the blades do not turn, it appears that your mixer's suffered a mechanical failure in the mixers transmission. I don't know if your mixer is under warranty, but I suspect like any small appliance the warranty's only good for a year, and you've probably had it much longer than that. That leaves with with three options; purchase a replacement (Sunbeam and the economy would appreciate that!), take it to a local authorized Sunbeam repair shop, and finally attempt to repair the transmission yourself (DITY repair). The later can be most gratifying, however, sadly, Sunbeam doesn't provide Parts List manuals like some other mixer brands, e.g.; Kitchenaid, so I can only suggest Option 1 or 2. I wish I could offer you more help. Hopefully this will help point you in the right direction. Howard - Burke, VA
If this solution has helped, please rate it, thanks! - hslincoln

Just take me off your list..I don't want to set up an account. I don't want to keep receiving messages. Just FORGET IT.

Not sure, but you could contact Sunbeam at 1-866-588-1081
and see if they can get you the power cord for your mixer.

I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up)
Please Note: If you cannot rate this post with the highest rating, then please do not leave any rating. I am doing this for free and I do not think that any rating other that the best is needed.
If you need further assistance please comment to this post and I will try to help you further.
Thanks for using FixYa
asnowman

check and replace the plug fuse and internal fuse of the mixer

Try this website. This is the Sunbeam site with links to the parts supply companies they recommend. There are small companies out there that can do the repairs for you.

They would normally sit in a groove under the turntable with a groove on top to hold them in place. I was hoping to find a Parts Schematic Diagram, but that model seems old and rare. https://www.google.com/search?q=sunbeam+vista+mixmaster+423a+parts+diagram Dave's Repair may be able to help as he seems to be the expert. ..

It is most likely that the 'shear pin' in the drive system has sheared. If it was 'new' someone bought it, over-worked it, packed it up and sent it back. https://www.google.com/search?q=Sunbeam+2370+stops+spinning Parts are obsolete already, it must be new to you, not 'new'. https://www.ereplacementparts.com/sunbeam-2370-stand-mixer-parts-c-116440_116448_116560.html It you enjoy baking get a KitchenAid stand mixer. ..

Check the carbon brushes on the motor and clean the copper commutator on the armature that they run on. https://www.google.com/search?q=Sunbeam+mixmaster+will+not+turn+beaters ..

You don't, you just throw it out and buy a new one. They aren't made to be taken apart and this is the sum total of 'spares'! https://spares.bigwarehouse.com.au/index.php?cPath=81834_84179_90569 No one has ever taken one apart. https://www.google.com/search?q=SUNBEAM+STICK+MIXER+MODEL+SM6200+TYPE+737+disassembly Inside is all you will find is an overclocked direct drive electric motor. ..