Top 20 Samsung SCX 4623F - Multifunction fax / copier / prin - SCX-4623F Questions & Answers


Dear
The front door right side there is a lever found when it is opened the lever should close the micro switch inside and the door is locked with another short lock (near the long lever). If door lock broken then the micro switch push the lever and door not closed.

the basic problem with the micro switch and related mechanical alignment.
Thanks.

Samsung SCX... | 363 views | 0 helpful votes


Dear
Pl. update the firmware. else replace the main PBA.
Thanks.

Samsung SCX... | 120 views | 0 helpful votes


Printers dont reset unless you unplug them from the power connection or mains. Try again.

Samsung Office... | 16 views | 0 helpful votes


This could be a bad or loose switch or interlock. This unit may use a photo type of switch and it can fail or become obstructed.

Samsung Office... | 18 views | 0 helpful votes


Test the power cable on another printer and sees if it powers it..check the power supply if it is up to or not more than the required output voltage to power the printer..if problem persist check power board of the printer and read if their is still continuity on the fuse ..read the fuse with multimeter..the fuse if the printerust have been discontinued

Samsung Office... | 13 views | 0 helpful votes


this is caused by a failure of the fuser unit.
The fuser usually heats the paper to fuse the toner to the paper.

Samsung Office... | 216 views | 2 helpful votes


To reset Samsung printer manually, firstly press the Power button until the LED light turns off. Before proceeding to next step, confirm that your Samsung printer is off. Now, you have to remove the power cable from the back of Samsung printer and then leave your printer unplugged for 10 minutes.
https://www.printerstechnicalsupport.com/how-to-reset-samsung-printer-firmware

Samsung Office... | 55 views | 1 helpful votes


To print a duplex page, follow these steps:
  1. Go to Device and Printers. ...
  2. Right click on the printer, then select Printer Preferences. ...
  3. Below Double-Sided Printing select Long Edge or Short Edge depending on preference. ...
  4. Click Apply and OK to save the changes.
https://support.hp.com/in-en/document/c05589026

Samsung Office... | 53 views | 0 helpful votes


https://www.youtube.com/watch?v=K93j4hdTpZQ

This error is caused by a counter inside your printer not being correctly reset when the new belt is installed. To fix this problem follow the steps below: Press MENU then #1934. Use the arrow keys to navigate to the Tech menu (this is different to the User Mode)

Samsung Office... | 56 views | 0 helpful votes


I searched the internet using https://www.google.com to see if I could locate support information for this printer.

The following link mentions software but didn't show how to troubleshoot the printer for that problem.
https://support.hp.com/us-en/drivers/selfservice/samsung-scx-3201-laser-multifunction-printer-series/19135195

Samsung Office... | 56 views | 0 helpful votes


https://www.youtube.com/watch?v=AN973Ko0kX8

Samsung Office... | 102 views | 0 helpful votes


https://eu.community.samsung.com/t5/Cameras-IT-Everything-Else/Samsung-SCX-3200-Printer-Double-Printing-Problem-Software/td-p/260539

Samsung Office... | 58 views | 0 helpful votes


For me it was a standard paper jam. I pulled out the paper tray, reached under and pulled out a jammed sheet, then reinserted the paper tray and it worked.

Samsung Office... | 67 views | 0 helpful votes


Changing the Display Language and Country
Setting Language
To change the language that displays on the control panel,
follow these steps:
1 Press Menu until "Machine Setup" appears on the top line
of the display.
2 Press the scroll button ( or ) until "Language" appears
on the bottom line of the display.
3 Press Enter. The current setting appears on the bottom
line of the display.
4 Press the scroll button ( or ) until the language you
want appears on the display.
5 Press Enter to save the selection.
6 To return to Standby mode, press Stop/Clear.
Setting Country
1 Press Menu until "Machine Setup" appears on the top line
of the display.
2 Press the scroll button ( or ) until "Select Country"
appears on the bottom line of the display.
3 Press Enter. The current setting appears on the bottom
line of the display.
4 Press the scroll button ( or ) until your country appears
on the display.
5 Press Enter to save the selection.
6 To return to Standby mode, press Stop/Clear.
NOTE: Changing the country clears the memory.
Link to manual
http://h10032.www1.hp.com/ctg/Manual/c05786751

Samsung Office... | 31 views | 0 helpful votes


Hello,

Check the sensors on the paper path ( from the tray to the exit ).

Samsung Office... | 36 views | 0 helpful votes

Not finding what you are looking for?
Samsung SCX 4623F - Multifunction  fax / copier / prin - SCX-4623F Logo

16 questions posted

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Cindy Wells

Level 3 Expert

6197 Answers

The Knight
The Knight

Level 3 Expert

76443 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Samsung Office Equipment & Supplies

  • Samsung Office Equipment & Supplies

Most Popular Question

samsung printer scx 4623 message keeps

  • Office Equipment & Supplies
Loading...