Top 20 Sharp AR 201 Copier Questions & Answers

the chip on your toner cart is bad or not the correct one. you need to change your toner cart.

No it's not. Your best bet is to try an HP driver. If you're ready for a new machine I can give you a quote! Skelton Business Equipment Houston Copiers

check fusing unit first and then reset error code.

On a Sharp AR-201, the developer light comes on when 50,000 pages have been made since the technician (or factory,) last changed the developer substance and reset the counter. A tech should come out with a Preventative Maintenance kit because training is needed to remove the developer substance safely as well as to clean the optics, interior and inspect the fixing unit, drum and cleaning blade and vacuum out the copier. You should call for service and tell them the developer light is on so they know to bring a kit. And yes... I am factory trained on this model. Retired now.

Go to service mode, then in system 1, and in 'Machine" setting option you can the sensors.

Have you tried a trouble clear?

Hello,
the error F5 02 means that the copy lamp lighting is abnormal.
This is what is in the service manual:

F5 02 Content Copy lamp lighting abnormality
Details The copy lamp does not light up.
Cause Copy lamp error
Copy lamp harness abnormality
CCD PWB harness abnormality
Check and remedy
Check the copy lamp (SIM 5-3)
When the lamp lights:
Check the harnesses and connectors
between the CCD unit and the MCU PWB.
When the lamp does not light:
Check the harness and connector
between the copy lamp and the MCU PWB.
Replace the copy lamp unit.
Replace the MCU PWB.
Remarks Copy lamp disconnection
Cable is not attached.
You must call a tech to solv your problem.

need complete report where jaming and after how many copies

its means you need to replace toner just replace a new toner cartridge

What is wrong with it? It is a workhorse. I would say yes.

# * C * den start batan the copier will re-start

press the ff. botton to reset that error press #/p, * , clear, * then enter 16 then press start

Not sure what YOU mean by LSU but if you are referring to Laser Scanner Motor or the Polygon Mirror Motor then they are $125 to $200 depending on where you are buying.
Your part# to search by is RMOTN0022QSZZ. The 0022 is zero zero two two.
Good Luck and Thank You for using Fixya.

check the developer in the developing unit maybe the developer is empty,then also check the charging assembly maybe its pour of toner just try to clean

probably tippex or a pen mark on **** glass

Hello sir; This error code it can be reset folloe the instruction;
1, press "clear", "interupt", " 0 ", "interupt"
2, enter 16 then press start.

A error code F1-09 deals with the finisher of the copier. Have the bins gotten stuck or got something in it's way when moving up & down. I would turn the copier off and unplug the finisher from the copier, 1 screw holds connector in. Then I would turn it back ON and see if the code is gone, if so reconnect the finisher and you should be good to go...

tis problem is some of panel button is short i mean it is lock please open your machine panel board and service it . then solve your problem

mos the toner light come on is just out of tonert likely is out of toner is it runs for ever and doent come to ready and finely

F1 means "shifter Motor Trouble". The motor that driver the shifting mechanism at the paper exit side is not functioning. The motor could be bad or there may be something binding the motor up. Take a real close look at the exit unit (where the paper comes out of the machine) and see if there is anything in the way of the shifter. It could also be a bad board issue - sending the wrong signal to the motor... or possibly a bad home position sensor for the shifter.
You could try taking the shifter unit out for a closer inspection - make sure its properly installed.
Hope this helps.