20 Most Recent
Dacor Millennia DHI602 Kitchen Hood - Page 8 Questions & Answers
The oven sounds like it is sputtering the whole
While you didnt say if your oven is heated by gas or electric i am going to assume its gas and the cause of that sputtering sound is due to weak ingiter that is not fully opening the gas valve yet its just opening it a wee bit cauing it to basically starve for gas flow and sputtering all the time the gas is flowing. By replacing the igniter the gas will flow properly and stong and thusly the noise will cease and it will heat quickly.
If its electric heated let me know and i will figure why its sputtering
Stove tripping circuit breaker
Miswired element.
Faulty element.
Faulty thermostat.
Components normally fail and trip breakers was soon as power is connected. Yours has something happening after 10 minutes as the stove is heating up and reaching the set temperature.
Google
make model wiring schematic
..
Kenmore C880 6587590 burner switch replacement.
I just replaced the switch just yesterday.First remove the glass panel by pushing back the 2 black clips at the top end,then remove 2 silver screws at the top and 3 at the bottom also remove 2 black screws behind side panels on the top. Now push side panels slightly up and forward and it fill fall forward and now replace the switch.
Why is our Baxter 18 pan oven giving us a Heat Error
If you were looking for a way to earn some extra income every week... Look no more!!!! Here is a great opportunity for everyone to make $95/per hour by working in your free time on your computer from home... I've been doing this for 6 months now and last month I earned my first five-figure paycheck ever!!!! Learn more about it on the following link...
www.cash.hiring9.com
Omega Rangehood not working.
Hello,
One night, my (Omega) range hood also blew with a snap, crackle and pop (flash) also after pressing the light button.
The PCB is charred behind the light switch/toggle thingy.
The PCB is a replaceable part, but out of interest I am curious to learn if I can piggyback the light onto the fan switch.
"Anonymous", at first I thought I may have authored what turned out to be your post.
Many thanks.
Stovetop burner won't light after I turn on the gas.
That is normally caused by the holes in the flame spreaders being full of cooking residue. Put them all except one in a pot of cold water with a teaspoon or washing up liquid, Bring very slowly to a simmer. Watch it because it will immediately want to boil over. Remove from the heat and drop the remaining spreader in. Leave them to cool. Scrub them with a plastic post brush, making sure the holes are clean all the way through. Rinse and leave to dry.
Or your gas has been turned off? Does the oven work?
How to clean stains on the Russell Hobbs 2 Plate Mini
To clean stains on the Russell Hobbs 2 Plate Mini, you can follow these steps:
- Turn off and unplug the mini stove to ensure your safety.
- Allow the plates to cool down completely before cleaning.
- Make a solution of equal parts of white vinegar and water in a spray bottle.
- Spray the stained areas with the vinegar and water solution.
- Let the solution sit for a few minutes to break down the stain.
- Wipe the plates with a soft cloth or sponge, applying gentle pressure.
- For stubborn stains, sprinkle baking soda on the plates and scrub gently with a sponge or brush.
- Wipe the plates clean with a damp cloth and let them air dry completely before using the mini stove again.
Note: Avoid using abrasive cleaners or scrubbers as they may scratch the surface of the plates. Also, avoid using harsh chemicals that may damage the surface or the heating elements of the mini stove.
Need wiring diagram elba c96df oven control
Can you please send me the wire diagram by color to connect to wire board panel like red, grey white etc. for gas stove JGBP28BEJ1CT gas stove I bought a replacement but forgot to take a picture
I have a Broan Allure range hood and the left light is broken inside
To replace the broken light on your Broan Allure range hood, you will need to follow these steps:
- Turn off the power to the range hood by unplugging it or turning off the circuit breaker.
- Remove the filters by gently pulling them down and then out of the range hood.
- Locate the light cover and remove it by pulling it towards you.
- Use a screwdriver to remove the screws that are holding the light assembly in place.
- Carefully pull the light assembly out of the range hood.
- Replace the broken light bulb and ensure that it is securely in place.
- Reinsert the light assembly into the range hood and tighten the screws.
- Reattach the light cover by pushing it back into place.
- Replace the filters by pushing them back up into the range hood.
- Turn on the power to the range hood and test the new light to ensure it is working properly.
Note: If the light assembly is wobbly, you may need to tighten the screws that hold it in place or replace any damaged parts.
Kitchen Aid convection oven doesn't reach pre-heating set temperature
There are a few other things you can try to troubleshoot this issue:
- Check the oven gasket: If the gasket around the oven door is worn or damaged, it could be letting heat escape from the oven, which can prevent it from reaching the desired temperature.
- Check the oven igniter: If the oven igniter is faulty, it may not be able to draw enough current to ignite the gas and heat the oven. You can test the igniter with a multimeter to see if it is working properly.
- Check the oven thermostat: The thermostat regulates the temperature inside the oven. If it is faulty, it may not be able to maintain the desired temperature. You can test the thermostat with a multimeter to see if it is working properly.
- Check the control board: The control board regulates the oven's heating elements and can be a source of problems if it is faulty. You can test the control board with a multimeter to see if it is working properly.
If none of these solutions work, it may be best to call a professional technician to diagnose and fix the problem.
I set my temp on my pit boss 820 to 200 and it just keeps climbing to at least 400 what needs replaced
If your Pit Boss 820 pellet grill is not maintaining the set temperature and continues to climb, there could be a few potential causes.
- Damaged temperature probe: The temperature probe is responsible for sending the temperature readings to the controller. If it's damaged or malfunctioning, the controller may not be able to regulate the temperature properly.
- Faulty controller: If the temperature probe is working correctly, the controller could be the problem. If the controller is faulty, it may not be able to read the temperature correctly and regulate the temperature properly.
- Airflow obstruction: Another possible cause is an obstruction in the airflow. If the airflow is restricted, it can cause the grill to overheat.
To troubleshoot this issue, start by checking the temperature probe and controller for any visible damage or signs of malfunction. If they appear to be functioning correctly, check for any obstructions in the airflow. If the issue persists, it's recommended to contact the manufacturer or a qualified technician for further assistance.
Not finding what you are looking for?