Top 20
Haier HDP18PA Stainless Steel Free-Standing Dishwasher - Page 2 Questions & Answers
Help
Tilt the machine 45-0 degrees and let it drain any excess water.. It also beeps when the leds flash also right? Drain the water and it will start right back up.
My dishwasher keeps beeping at
I tilted mine backwards with it running and beeping and it stopped beeping shortly...It made a mess on the floor of course but I put it down and lights were still flashing but no more beeping. Thought I would try tipping it forward while it was running and the lights went off and the beeping never started again. Its working fine now??
The washer keeps beeping and
I have a Haier HDP18PA with the same problem... I tried tilting mine backwards while running...this made a mess BUT the beeping stopped BUT the lights were still flashing. Turned it off and started it again and the lights still were flashing BUT no beeping. Decided to try tilting it forward while running ... made another mess BUT the lights stopped flashing. Turned it off again and restarted it and it is now running fine. Good luck!
Haier Stainless SteelDishwasher HDP18PA not washing dishes
The heater probably isn't coming on, making it so the detergent can't dissolve completely or clean very well.
To test this, pause the unit about 10 minutes into the wash cycle (hit the stop/start button) and feel the water in the bottom. It should be hot, not lukewarm.
Also, if the heater isn't working, you won't see as much steam come out when you open the door at the end of the cycle.
Until you get it fixed, try using the pots/pans cycle (I use it for every load with this machine).
Heating element
- Remove the screws on the back of the unit and take off the back two panels.
- Facing the back, there is a thermostat toward the back-middle-right... it has a brass nut that holds it in place and two wires attached to it. (my wires were pink). Check this first: check the wiring here, and if you have a multimeter, check the continuity between the two terminals. It should be closed (conducting) when cold.
- You should see the wires for the heating coil on the left side. If you have a multimeter, check the resistance across the left and right terminals (the middle terminal with green wires is ground). If there is no continuity, the heater is dead.
- Finally, the only other cause would be the relay (hidden off in the right-rear corner of the unit) or the control panel.
Haier Stainless Steel dishwasher
If you can hear a humming sounf it will be the pump motor not working. If you can get to the back of the pump try and turn it by hand with the power on. If it then starts it is the motor start capacitor
Haier HDP18PA
On another site, someone posted this: "I called (website), where it was purchased from, and they gave me the number for the manufacturer. Some standard troubleshooting did the trick and my dishwasher is working perfectly again. The troubleshooting involved tilting the dishwasher backwards at a 45-degree angle and letting any excess water drain out. They said ocassionally the water intake will be blocked and this process helps move anything that may have gotten in the way"
I was having the beeping problem too, and decided to give it a try, tipped it for a few, and found it to work!!! Hope this maybe helps!
Haier sdw4a
hi
cant help more then this:
try the manual in the end of the page
see if it helps
http://www.haier.com/servicesupport/manualMore.asp
if not contact the firm
http://contact.haier.com/engdefault.asp
if they dont help
call a tech guy he'll know whats worng
good luck
Haier dishwasher XIB6B2S3FS-80 cycle not ending
First thing to try is a reset..
Unplug or turn it off at the breaker for 5 minutes.
You can also try this but it's used to clear error codes....
Simultaneously press and hold Cycle Select and Start pads for 5 seconds.
Press ANY button to complete the reset process. ...
The unit will now be ready to use/function normally at this time.
4/11/2023 11:55:16 AM •
Haier...
•
158 views • 0 helpful votes
Haier appliances repair parts search
With 30,000 9.4 out 10 reviews, they must be good!
It won't be the element though, it will the thermistor or the thermostat that is failing. Some can be calibrated. It may also be a failed circulation fan on a fan assisted oven.
Test the oven first with an oven thermometer. elements can be tested for resistance, but in my experience they work or they don't, they don't half work.
https://fixpart.de/de/uber-uns
..
3/11/2023 3:02:40 PM •
Haier...
•
30 views • 0 helpful votes
My Haier Dishwasher HDW100WHT is pumping water over the floor .The door is firmly closed. Any Suggestions please?
OK. When you see water on the floor, and you open the door, is there any water rising in the wash chamber and breaching the seal? If you open the door and do not see any water other than the water dripping off the dishes or whatever, I would suspect there's a leak underneath. If you see water standing in there, they you will want to clean the food/debris trap. Refer to your manual, if you have one. If the food trap is cleared and the water is still comin out, I would suspect a leak underneath the unit, possibly a loose water hose or drain hose.
4/27/2019 2:49:56 AM •
Haier...
•
212 views • 0 helpful votes
Not finding what you are looking for?