20 Most Recent
Haier ESD300 / ESD301 Built-in Dishwasher Questions & Answers
1 Answer
Runs when not turned on
Typically, the unit will activate its empty pump if a fault is detected and it needs to protect from a potential overfill/floood that has either happened, or MIGHT happen. Most commonly, the machine has detected a leak when the float in the base of the machine has tripped a microswitch because there is water in the base. Turn off at the mains, pull the machine out (I appreciate this is a pain as it's integrated!) tip back 45 degrees and water will probably run out of the base. This will correct the error state and the machine will then run again. Of course, it probably WON'T fix the leak that caused the problem in the first place. If you can get it running at this stage, get the side off and set the machine on a wash while it's still pulled out from inder the work surface, get a torch and go looking for the leak!
Haier ESD300 /...
|
Answered
on Sep 20, 2015
2 Answers
I have had a Haier Dishwaher ESD300 for about 2
My dishwasher had the exact same symptoms. The control panel was faulty. I discovered this by testing the connector with my multimeter, looking for the LED connections. When I wasn't able to find anything, I carefully peeled it off. (See picture.) I expect at least one of the traces underneath the nasty brown line is faulty, causing the control panel to not function. On the control board, I jumpered the first pin to the fifth pin from the bottom of the connector, as viewed with the Haier brand right-side up, and pots & pans started right up.
.
It looks like I can get a replacement control panel from Sears Parts Direct for $30.
Haier ESD300 /...
|
Answered
on Mar 11, 2015
1 Answer
Haier dishwasher new ESD301 not all panel lights working
You probably have a faulty control panel. I've seen a few other problems on FixYa where the control panel didn't work at all. My very own ESD300 had corrosion inside the control panel near the ribbon cable that caused it to stop working. I'm not impressed with Haier's manufacturing controls. In my case it looked like something done to it in manufacturing either allowed water to get inside or caused abnormal deterioration.
Haier ESD300 /...
|
Answered
on Oct 25, 2013
1 Answer
I have Haier Dishwasher model
Hello
& Welcome to FixYa
The
dishwasher thermostat located inside the bottom front panel is bad and needs replacement. If it tests fine then it is the heater assembly that needs replacement. Please get back to
me if you have any other questions.
Kevin
Haier ESD300 /...
|
Answered
on Aug 30, 2011
1 Answer
It won't start, no lights nothing
My dishwasher had the exact same symptoms. The control panel was faulty. I discovered this by testing the connector with my multimeter, looking for the LED connections. When I wasn't able to find anything, I carefully peeled it off. (See picture.) I expect at least one of the traces underneath the nasty brown line is faulty, causing the control panel to not function. On the control board, I jumpered the first pin to the fifth pin from the bottom of the connector, as viewed with the Haier brand right-side up, and pots & pans started right up.
.
If yours has the same problem, you can get a replacement control panel from Sears Parts Direct for about $30.
Haier ESD300 /...
|
Answered
on Dec 31, 2010
1 Answer
I have had the dishwasher for about 2 years. I
My dishwasher had the exact same symptoms. The control panel was faulty. I discovered this by testing the connector with my multimeter, looking for the LED connections. When I wasn't able to find anything, I carefully peeled it off. (See picture.) I expect at least one of the traces underneath the nasty brown line is faulty, causing the control panel to not function. On the control board, I jumpered the first pin to the fifth pin from the bottom of the connector, as viewed with the Haier brand right-side up, and pots & pans started right up.
.
It looks like I can get a replacement control panel from Sears Parts Direct for $30.
Haier ESD300 /...
|
Answered
on Dec 31, 2010
1 Answer
Brand new dishwasher will not drain at end of cycle.
Check your manual. Some dishwashers actually do leave water in them after the final drain cycle. It has to do with the type of seals they use. Some will leak the very first time they are used but not after that. The seals in these types must remain wet. If this isn''t the issue, wait about 5 minutes fir the timer to finish. Sometimes there is quite a lag at the last cycle. If all else fails, call the customer service number in the manual.
Haier ESD300 /...
|
Answered
on Feb 02, 2009
Not finding what you are looking for?
.
