20 Most Recent Haier HDP18PA Stainless Steel Free-Standing Dishwasher Questions & Answers


Haier sdw4a

hi cant help more then this: try the manual in the end of the page see if it helps http://www.haier.com/servicesupport/manualMore.asp if not contact the firm http://contact.haier.com/engdefault.asp if they dont help call a tech guy he'll know whats worng good luck
1/6/2022 4:06:26 PM • Haier HDP18PA... • Answered on Jan 06, 2022

The washer keeps beeping and

I have a Haier HDP18PA with the same problem... I tried tilting mine backwards while running...this made a mess BUT the beeping stopped BUT the lights were still flashing. Turned it off and started it again and the lights still were flashing BUT no beeping. Decided to try tilting it forward while running ... made another mess BUT the lights stopped flashing. Turned it off again and restarted it and it is now running fine. Good luck!
8/20/2021 5:25:29 PM • Haier HDP18PA... • Answered on Aug 20, 2021

Haier HDP18PA

On another site, someone posted this: "I called (website), where it was purchased from, and they gave me the number for the manufacturer. Some standard troubleshooting did the trick and my dishwasher is working perfectly again. The troubleshooting involved tilting the dishwasher backwards at a 45-degree angle and letting any excess water drain out. They said ocassionally the water intake will be blocked and this process helps move anything that may have gotten in the way"


I was having the beeping problem too, and decided to give it a try, tipped it for a few, and found it to work!!! Hope this maybe helps!

9/19/2015 7:00:14 PM • Haier HDP18PA... • Answered on Sep 19, 2015

Dishwasher does not go past

You have either a faulty element or thermostat. Your timer is controlled by the temperature, it wont click on until it reaches the correct temperature. If you want to try and fix then SWITCH POWER OFF and pull machine out.
1) Remove all water from inside
2) Put machine on left hand side and remove bottom panel if possible. Normally 2 or 4 screws. If not then remove front kick plate and panel behind.
3) Locate thermostat, should be a small round device attached to the bottom of the tank and will have 2 wires connected to it, there may also be a high limit stat beside it if so then you will need to replace both of these. You can get them from online spares sites and inputing your make and model and selecting the stat set.
3) If this doesn't help then you will need to replace the element.

Hope this helps.
8/13/2015 8:57:40 AM • Haier HDP18PA... • Answered on Aug 13, 2015

I have a haier dishwasher but the water wont drain

you maybe right but before doing machine reset button, you need to clean the machine be sure there's no jam in mechanical parts. also not all machine have reset button outside, some are hide and inside the power supply module so look for it and be careful.
11/19/2014 10:08:43 PM • Haier HDP18PA... • Answered on Nov 19, 2014

Why Does Fault Alarm Beep at End of Cycle?

Check any user friendly ports, filters, screens. It appears that the washer is trying to tell you something. See your manual for troubleshooting. BLEEP BLOOP
3/10/2014 6:46:27 PM • Haier HDP18PA... • Answered on Mar 10, 2014

HDW101SS does not heat water.


If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician will tell you the same. Unless the temp limiter blows again you do not even need testing the other two thermostats. Temp limit may blow because of occasional overheating. If it blows more than once there is either a shorted thermostat, a defective CCU(control module), or an heating element that stays always on because of a short.

Here how it works- CCU is control module powering the element in the mid part of the cycle:

C-------------Temp limit---TS---TS-----\

Replace the defective high limiter. That will do the job. If it doesn't, test and replace the other two thermostats located at the bottom side of the appliance. A shorted thermostat will read zero Ohms or very low impedance (

10/15/2013 3:09:26 PM • Haier HDP18PA... • Answered on Oct 15, 2013

Water heating light is on

Sometimes I see a cars' left turn blinker light on while they are driving for miles but I don't feel It necessary to have to post it on a website. Do you have a question?? If so, please include what you did before this event to get his poor machine to send this cryptic message..
10/14/2013 8:17:36 PM • Haier HDP18PA... • Answered on Oct 14, 2013

Not working

That is most likely related to debris in the lower are or diverter. The pump is the same for both. Most likely food in the area or pipe to the lower arm.
6/9/2013 3:13:08 PM • Haier HDP18PA... • Answered on Jun 09, 2013

Need operators manual for a haier dishwasher

www.specsserver.com/CACHE/FRWDAJEQUXIO.PDF Full downloadable manuel
2/11/2012 12:07:15 AM • Haier HDP18PA... • Answered on Feb 11, 2012

I am trying to find

You can print the manual from the link below.


If tat is not your model then please give the make and model #
5/2/2011 12:56:59 AM • Haier HDP18PA... • Answered on May 02, 2011

I have a haier dishwasher

Check the small sensor along the rim of the door/door jam. It may be stuck. Free the machnism an start washing. Another common problem that cuase those symtoms is a bad door gasket.
4/13/2011 7:33:55 PM • Haier HDP18PA... • Answered on Apr 13, 2011
Not finding what you are looking for?
Haier HDP18PA Stainless Steel Free-Standing Dishwasher Logo

64 questions posted

Ask a Question

Usually answered in minutes!

Top Haier Dishwashers Experts

David Shaub

Level 3 Expert

2991 Answers

Tim Doolittle
Tim Doolittle

Level 2 Expert

118 Answers

The Knight
The Knight

Level 3 Expert

76835 Answers

Are you a Haier Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Haier Dishwashers

  • Haier Dishwashers

Most Popular Question

hdw101ss not heat water

  • Dishwashers