Question about Bosch Exxcel WVT 2850 Front Load Washer / Dryer

11 Answers

Bosch Exxcel tumble dryer error code F:09

The dreyer starts ok but then buzzes with the error code F:09 have tried cleaning out the filter etc. we have not used it for a couple of weeks due to holidays.

Posted by on

  • 4 more comments 
  • kk7408 Oct 04, 2008

    I have the same problem....anybody have a solution?

  • Anonymous Oct 08, 2008

    I have the same problem...

  • nnay07 Oct 23, 2008

    same thing here: putting less cloth inside and using a different program seems to work.

  • wrserr Nov 16, 2008

    dryer not heating. had low voltage resulting in power cut this morning, dryer now tumbles but is not heating. Error F09 on display. Any ideas?

  • Anonymous Nov 23, 2008

    anyone who knows what to do?

  • staceytrefts Feb 07, 2009

    Same problem F:09 beeps and shuts down. All filters are clear

×

11 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Mine did this. Because the bottom left filter was blocked the overheat cut out had tripped. This is inside the rear of the machine accessible after removing the rear panel

Posted on Mar 11, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

As above.
Bosch Dryer WTS84507GB/03.
Mine did this. Because the bottom left filter was blocked the overheat cut out had tripped. This is at the rear of the machine and is accessible after removing the rear panel. Just push the little red button at the top. Remember to un-plug the machine first.

Posted on Mar 02, 2010

  • dempo Jun 03, 2012

    I can't find a screwdriver that will take the screws out, what type did you use

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Same for me, lots of tumble but no dry. Cleared out bottom door filter, removed nasty gunk including a hotel room card?? and then took back off machine. Trip switch is small red button and when pressed the heat returned. Job done.

Posted on Sep 23, 2009

  • D Johnston Dec 04, 2011

    This worked great thanks very much

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Same here, red button behind the back cover restored heat.

Posted on Oct 26, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

HAve been having this problem with my dryer. After one minute it shows filter blocked, altho the filter (in the drum door) was free. Now took the other filter, bottom left hand corner, out - and cleared it with a wooden skewer - cat hair and sludge about the size of a large cooking apple has been extracted, and the dryer is now running normally.

Posted on Jun 04, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Also works on bosch WTE86301, little red button behind the insulated part of the back cover.

Posted on Feb 24, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had this problem too - called a guy to investigate (cost me €78) and it turned out to be a snapped belt which goes around the drum. Looks relatively easy to repair need to take a few panels off (requires a torque screw driver) and the belt has the part number on which (according to the repair guy) is easy to get. Hope this helps

Posted on Feb 24, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Maplin sell the so-called security screwdriver heads. The original idea was to keep non-professionals out, but now a necessity to let them in otherwise more units finish up on the dump while you wait for Bosch to answer call out requests.Cost less than Pounds 5.

Posted on Jul 20, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same message although I cleaned out the condenser and filter at bottom. Took back cover off with special screwdriver and pressed red reset button. Dryer is working fine now, worth the 15 minutes effort!

Posted on Jan 11, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same error - took a bit of the drying load out and it worked fine! Shows that this can be a very simple error message sometimes, without having to take back off etc...

Posted on Oct 27, 2012

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

I had exactly the same problem with F 09 error code. Had to buy special screwdriver set (cheap), took the back off and pressed the red reset button. Ptoblem solved. Thank you.

Posted on Jul 14, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

LG dryer DLE2140 error CL clean filter which I have done and even used vaccum dryer still wont come on


the clean filter just blinks at start of a cycle to remind you to clean it. there is no lint filter sensor or anything like that. it goes out after you program your cycle and hit start. if dryer is not coming on, there is another issue. any fault/error codes?

Mar 10, 2015 | LG Dryers

1 Answer

Kenwood kdw12st3a error e1 & water leak


I suspect it is taking too long to fill.
Remove the inlet hose and check the water pressure there.
Also make sure the small filter there is clean and retry.
If you have ever turned the washer on any side, then
I think you may have water in the pressure switch by turning it over.
You need to locate it and see if there is water in there.
It should e round and have wires attached and a thin rubber tube. Unfortunately There is no parts diagram for this machine

Apr 16, 2012 | Kenwood Dishwashers

2 Answers

Hi, i'm getting error message 1203 on the printer and we've lost the user's manual. Can you tell me what this is?


Error 1203 is a very interesting error code. Here is what I found out about error 1203



Error 1203 is a very interesting cartridge error. It means your cartridges overflow even from brand new cartridges after a several prints or right after you refilled the cartridges. Check to see if ink are smeared on the holder where the contact panel with the cartridge


Solution:
I use the lint free cloth(coffee filter work great) with a few drops of water to dampen and clean off those contact on the holder and my printer work again.
Then before you print anything, you should run aligned the cartridges a couple times then run clean cartridges a couple times.
Print the test page to see how it's look and way you go.
Be sure not to leave any debris of lint free cloth(coffee filter work great on those holder contact panel.

Article on refilling Dell ink cartridges


Rick

Sep 10, 2011 | Dell 926 All-In-One InkJet Printer

1 Answer

When washer turns on there is a horrible buzzing sound, e 20 error message was on before


This is a blocked drain error code (E20) which can be due to a clogged/kinked drain hose, blocked drain filter/coin trap, or a broken drain pump. The link below provides the detailed troubleshooting procedure of this error code. In addition, replace the drain pump after having found no problem with the drain hose, cleaned the filter, and checked the drain pump impeller but the drain pump just hums, buzzes or whirs.

Error Code E20 on Frigidaire Front Load Washing Machines


Aug 25, 2011 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

I was using the Self Clean on the oven after a couple of hours I got an error message E1 and F5 - and the oven door is locked. I have no idea what that means or how to get the door open again. I tried...


Hello there and thank you for choosing fixya
Ok before i get into the error codes just a few words here about the self cleaning feature
This the feature that is the most harsh on these ovens due to the extremly high temperatures that is produced then this can and will cause serious problems if not done correctly
I know that people like this feature but i highly suggest that if you are going to use it please try to get the oven as clean as possiable before using this feature this helps the cleaning cycle tremendously ok?
Now for the error code
the e1 error dode is due to the door being locked so to repair this you need to unplug the oven and leave it sit for at least 1 hour this allows for the internal reset feature to reset the oven controle
after the hour is over plug it back in and in 1 to 5 min you may hear a audiable beep or click if so simply press the cancel button and attempt to open the door if so great you should be ok
Now for the bad one
The F5 code is due to the oven control sensing the extreem heat during self cleaning
and sensing that the controls are not controlling the temperature during cleaning which is a bad thing this can and will cause the control board to fail and once again due to the excessive heat
So hopefully once the oven has been unplugged for the hour and reset you should be allright but if not than you do have a bigger problem meaning that your controle board is shot ok?
Please keep me posted on how this is going so i can send you more information on this
Best regards Mike

Feb 18, 2011 | Whirlpool Ovens

1 Answer

F-09 error code


Hi


F09 error occurs due to overflow condition, if the overflow contact on the pressure switch is closed for more than 60 seconds and overflow condition will occur. To start with check the drain hose and make sure it is not clogged, also try to clean the drain pump filter. If everything is fine and the drain pump is running then check the wire harness to the drain pump and control unit. Please post a comment if you need more help.


Thanks

Rylee

Nov 01, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Spray Mister is clogged (likely due to hard water)-can this be cleaned/fixed?


try to clean the reservoir,etc.use agent that can dissolve sediments.then after cleaning, make sure use filtered water ,ok.use a cloth with cotton cloth.

May 29, 2009 | Sunbeam Steam Master 4055 Iron

2 Answers

I have a Monitor 2400 oil heater. I would like a more detailed description of all the parts for this heater. Also I would like to find a listing of the possible error (e) codes that this heater may display...


I cleaned the fuel screen located on the unit and replaced the filter on the external fuel tank. The external filter can freeze if it accumulates enough water and the temp is cold enough, or it can just get full of debris. I also unplugged the 2400 for 30 min to let the factory preset settings come back. Filter(s) caused the e14 error, preset settings cured the e13 error caused by me fooling with the start stop function so much. Thanks for the help!

Dec 10, 2008 | Heating & Cooling

2 Answers

Leaks From Filter Gasket


Sounds like you might have coffee oil build up. I would suggest soaking the Brew Head Screen and filter holder in a coffee oil remover by www.urnex.com or dezcal. Remove the screw if your filter basket has one. For home use it would be good to clean this every week or so. You can email me for more info: irene@smithagy.net. You also might just try purchasing a new filter basket (along with cleaning the Brew head screen and new basket).
Further technical info can be found at:
Electra-Craft
41 Woodbine St
Bergenfield NJ 07621
phone 201-439-1700
fax 201-439-1701
info@electra-craft.com
www.electra-craft.com

Dec 20, 2007 | Briel Domus Due Espresso Machine & Coffee...

Not finding what you are looking for?
Bosch Exxcel WVT 2850 Front Load Washer / Dryer Logo

13,956 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3069 Answers

yadayada
yadayada

Level 3 Expert

67912 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...