Do you sell parts for model MW8126W Emerson Microwave? I have one that needs a new molding for the front. Its the white plastic molding that wraps around the entire door. How much would it cost? Thanks, Mary

SOURCE: Emerson MW8109P 110 Watts Microwave Oven

buy a new oven they are so cheap

William Miller

• 9179 Answers
• Posted on Sep 10, 2008

SOURCE: GE Profile Spacemaker XL1800 Microwave Model # JVM1870SF001

(I also replied via e-mail)

Sorry, but the subject lines get cut off after so many characters.

Thanks for replying.

Part # DE63-00204A looks like a valid Samsung part number but it doesn't show up anywhere, so it's likely a proprietary part made only for GE and not available separately.

You can see a helpful exploded view of this model here.

Then you can go here and enter your model number and come up with the parts list. This site has much better prices than GE.

Normally you have to separate the door panels (as shown in the attached photo) and then you'll see the previously hidden screws you need to remove.

Or you can watch a YouTube video (not a video I made) that demonstrates how it's done.

Chances are you will end up having to but more than you want to, but not the whole door.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

William Miller

• 9179 Answers
• Posted on Jul 20, 2009

SOURCE: How to replace cracked plastic door frame on Whirlpool microwave?

Normally you have to separate the door panels (as shown in the attached photo) and then you'll see the previously hidden screw(s) you need to remove.

Or you can watch a YouTube video (not a video I made) that demonstrates how it's done.

In some cases, you then have to gently rotate the handle to unlock it.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

SOURCE: Broken door on my Emerson microwave (MW8985W)

You can order the outer panel. Its available at searspartsdirect.com for about $41. Just type in your model number and look under the "Door Assy" heading. To replace, just follow these steps:

You have to remove the inner door panel that goes around the perimeter of the glass. You can use a small screwdriver to carefully pry the plastic up and work your way slowly around the perimiter of the glass. Most microwave ovens also have grooves in the panel that you can insert the screwdriver into. Use care not to pry against the glass. The glass is tempered and also has an RF shield that prevents harmful microwaves from potentially harming the consumer. If you break the glass, you will need to purchase a new door.

The door handle screws are located behind the inner panel. Remove the door handle and any screws that may be holding the outer panel in place. Some panels are simply snapped in place.

Remove the broken panel and install the new one. Re-install the door handle and re-insert the inner door panel carefully and gradually work your way around the perimeter of the door glass and make sure it snaps back into place.

This repair can be done with the door in place, or you can remove it for easier access. If you decide the remove the door, simply open it all the way and lift straight up at the hinges. The door will lift off of the hinge pins. Place on a hard flat surface with some towels under it for padding. This protects the door facing from scatches.

If you have any questions, or require additional assistance, please let me know. I hope this helps you

SOURCE: Replace handle on Ewave microwave

Hi,

A common Guide that would help you :-

http://www.applianceaid.com/oven-hinges.html

Generic Procedure on most of the Ovens :-

Set the door on the ground with the hinges facing up. You will need to push down on the hinges and extend them by hand. It's probably best to put something in the palm of your hand like a handle of a screwdriver so that you can push on the hinge and open it up (you will still have to push hard). When you open the hinge up you will see a tiny hole appear about the size of a pin head. You will need to stick a screw or something inside this hole so that the hing will not close again. When you have both hinges locked out you can then reinstall your door at about a 45 degree angle. Open the door up all the way and remove the screws or pins you placed through the door and then you can shut the door all the way again.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!